Eaton TX series cam switch and PX series load isolation switch

2-speed non commutation (for 2 separate windings)

Used for multi tap windings

Can achieve multi-level speed control

Typical model:

T0X-3-8451/EZ (3-pole multi speed switch)

T3X-4-8440/12 (4-pole multi speed switch)

5.6 Step switch

Function: Used for gradually switching circuits, such as heater grading control.

Features:

Multi position step control

Connect different numbers of contacts at each position

Suitable for temperature control, power regulation, etc

Typical model:

T0X-1-15401/11 (1-pole stepper switch)

T0X-2-15403/IVS (2-pole stepper switch)

5.7 Control switch

Function: Used to control various operations of the circuit, including on-off, switching, manual automatic switching, etc.

Type:

On-off switch: simple ON/OFF control

Conversion switch: I-0-II or I-II conversion

Manual/Automatic Switch: Switch between manual and automatic modes

Turn on switch: jog operation

Typical model:

T0X-1-15321/11 (Turn on switch)

T0X-2-8177/11 (control switch)

5.8 General control switch

Function: Multi functional control switch, can be configured with multiple contact combinations.

Features:

Self locking 3-digit switch

Connect 3 contacts at positions 0 and 1

Connect 3 contacts at positions 0 and 2

Connect 3 contacts at positions 1 and 2

Spring reset function is optional

Typical model:

T0X-3-15391/11 (3-digit universal control switch)

5.9 Instrument selection switch

Function: Used to select different measuring instruments or measuring points.

Features:

Multiple options, such as V1-V2-V3

Suitable for switching between voltmeters and ammeters

Ensure safe isolation of the measurement circuit

Typical model:

T0X-1-15113/E (instrument selection switch)

Chapter 6 Attachments and Extended Functions

6.1 N-pole module and auxiliary contact module

N-pole module (N-P1X/N-P3X)

Function: N-pole contact for early closure and delayed disconnection

Installation position: can be installed on the left or right side

Breaking capacity: the same as the main contact

Order number: N-P1XE (for P1X flat installation), N-P1XZ (for P1X rear installation)

Auxiliary contact module (H11-P1X/P3)

Contact configuration: 1 normally open+1 normally closed

Function: Delay breaking, delay closing, N/O contacts are usually used for load shedding

Installation position: can be installed on the left or right side

Order number: H11-P1X/P3E (for flush installation), H11-P1X/P3Z (for rear installation)

6.2 Installation Accessories

Central installation accessories (EZ-T0X)

Used for single hole installation with a diameter of 22.3mm

Equipped with a buckle system for quick installation

Suitable for T0X/T3X flush mounted switches

Installation accessories for distribution cabinet (IVS-TOX)

Including crimping shaft, used for installation and renovation of distribution cabinets

Use the basic switch front panel

Connectors (DE-TOX/DE-P3X)

Used to convert flat installation to rear installation

Suitable for T0X/T3X/P1X/P3X

6.3 Interlocking mechanism and extension rod

Interlocking mechanism (UV-TOX/UV-P3X)

Connected with PE and neutral wire

When installed flush, it is installed at the rear of the switch

Installed at the front of the switch during rear installation

Implement door interlocking function

Interlocking extension device (ZW-TOX/ZW-P3X)

Up to 4 units can be plugged in

Each 25mm, totaling 100mm

Used to extend interlocking distance

Extension rod (ZAV-TOX/ZAV-P3X)

Up to 4 units can be installed

Each 25mm, totaling 100mm

Suitable for rear mounted switches

6.4 Shield and Key

Shield (H3-TOX/H1-T5X/H2-T5X)

Used for flush mounted switches

H3-TOX: Up to 8 contacts, cable entry holes 2 × 20mm+2 × 15mm

H1-T5X: Basic Shield

H2-T5X: Expansion shield for 6-16 contacts

Lock buckle (HZ-T5X)

Each contact requires one

Suitable for input and/or output wiring

Key (VR-TOX)

Used for changing the engagement position of key extraction in the later stage

Suitable for all switch angles

6.5 Emblem and Front Panel

Standard Emblem (FS908)

Size: 88 × 88mm

88 × 88 framework suitable for P3X, T5X, T5XB

Order number: FS908GE-P3X

Blank engraved emblem

FS-ALU980-TOX: Aluminum, used for T0X

FS (*) - TOX: Plastic, used for T0X

BS84X24-P3X: Insertion Emblem

Card holder (ZF5X-TOX)

Black, detachable

Used for inserting signage

Insert signboard (BS45X14-TOX)

Size: 45 × 14mm

Engravable text

6.6 Insulated distribution box

IP65 insulated distribution box (CI-K1-TOX)

1-2 contact modules: CI-K1-TOX-2

3-4 contact modules: CI-K1-TOX-4

With diaphragm and cable port

1 contact module=2 contacts

Chapter 7 Dimensions and Installation Points

7.1 Flat Installation (.../E)

T0X/T3X flush installation

Door opening size: depends on the number of contact modules

Installation depth: increases with the number of contacts

Can be equipped with H3-TOX protective cover

T5X (B) flat installation

Door opening size: 88 × 88mm

Installation depth: depends on the number of contacts (c2 size)

Flat installation type main switch with SVB: adding padlock function

7.2 Rear Installation (.../Z)

feature

Installation hole with a diameter of 22.3

Can be extended with interlocking long poles, up to a maximum of 4 × 25=100mm

Can be extended with an extension rod, up to 4 × 25=100mm

Size Table (T0X)

Model, number of contacts, installation depth (c20), maximum depth (≤ 4 ZAV)

T0X-1 2 41 mm 86~102 mm