ABB EasyLine series gas analyzer

ABB EasyLine series gas analyzer

Product positioning and core advantages

EasyLine is a new gas concentration monitoring equipment series launched by ABB, aimed at providing simple, economical, and reliable gas analysis solutions for various application scenarios. Its core advantages include:

Mature technology: Based on ABB's years of experience in gas composition analysis, the product technology is mature and has been widely applied worldwide.

Easy to operate: Basic operations can be achieved through 4 buttons, menu navigation is clear, and all device control methods are unified, making it easy for users to quickly get started.

Easy to connect: Integrated with RS 232/485 interface and supporting Modbus protocol, it can easily connect with computers, SPC or process control systems. It also provides Modbus DDE driver for easy data reading, storage and visualization in Windows applications.

High cost-effectiveness: With competitive prices while ensuring that measurement technology is not discounted, it is an economical choice for various application scenarios.

Main product models and technical parameters

Oxygen analyzer (EasyLine O ₂)

Measurement principle: Based on oxygen paramagnetism, using magneto mechanical principle, with short response time.

Measurement range: The minimum measurement range is O ₂ 0-2 Vol. -%, supporting a suppression measurement range with a minimum span of 2 Vol. -% O ₂.

Stability: Linear deviation ≤ 0.5% of span, repeatability ≤ 0.5% of span, zero drift ≤ 0.03 Vol. -% O ₂/week, sensitivity drift ≤ 0.1 Vol. -% O ₂/week or ≤ 1% measurement value/week (whichever is smaller, not cumulative).

Dynamic response: T ₉₀ time ≤ 5 seconds.

Installation environment: ambient temperature+5...+50 ° C.

Equipment specifications: Adopting a 1/2 19 inch casing, supporting desktop and rack installation, with dimensions of approximately 215 x 167 x 347 mm (width x height x depth) and a weight of approximately 8 kg.

Interface and connection: 1 channel 4-20 mA analog output (maximum 750 Ω), 2 channels of alarm value signal and 1 channel of collective status signal digital output, supporting RS-485 or RS-232 interface (configurable).

Gas connection: The inlet and outlet ports are equipped with DN 4/6 hoses.

Power supply: Input voltage 85-250 VAC, 48-63 Hz, maximum power consumption 90 VA.

Infrared gas analyzer (EasyLine IR)

Measurement principle: Infrared photometer can measure 1 or 2 components. If used in conjunction with an electrochemical oxygen sensor, it can only measure 1 infrared gas component.

Measurement range: The measurable gases and minimum measurement range include CO 0... 500 ppm, CO ₂ 0... 500 ppm, SO ₂ 0... 500 ppm, CH ₄ 0... 500 ppm, NO 0... 1000 ppm. It can also be combined with O ₂ (0... 5 vol. -%) for measurement (specific combinations are shown in the document table).

Stability: Linear deviation ≤ 1% of span, repeatability ≤ 0.5% of span, zero drift ≤ 1% of span/week, sensitivity drift ≤ 1% of measured value/week.

Dynamic response: T ₉₀ time ≤ 2 seconds (O ₂ sensor ≤ 30 seconds).

Installation environment: ambient temperature+5 to+45 ° C (+5 to+40 ° C with O ₂ sensor).

Equipment specifications: Same as oxygen analyzer, 1/2 19 inch casing, size approximately 215 x 167 x 347 mm, weight approximately 8 kg.

Interface and Connection: Each sample component has 1 analog output and 2 digital outputs of alarm value signals, supporting RS-485 or RS-232 interfaces (configurable).

Gas connection: The inlet and outlet ports are equipped with DN 4/6 hoses.

Power supply: Input voltage 85-250 VAC, 48-63 Hz, maximum power consumption of 40 VA.

Thermal conductivity gas analyzer (EasyLine TC)

Measurement principle: Based on the difference in thermal conductivity of different gases, micro mechanical thermal conductivity analysis technology is used, which has a short response time and is less affected by temperature.

Measurement range: It can measure various gas combinations and the minimum measurement range, such as CO ₂ in N ₂ 0... 10 Vol. -%, CH ₄ in N ₂ 0... 6 Vol. -%, etc. (see document table for details), supporting suppression of measurement range.

Stability: Linear deviation ≤ 2% of span, repeatability ≤ 1% of span, zero drift ≤ 2% of minimum given measurement range/week, sensitivity drift ≤ 0.5% of minimum given measurement range/week.

Dynamic response: T ₉₀ time ≤ 2 seconds.

Installation environment: ambient temperature+5...+50 ° C.

Equipment specifications: Same as the two analyzers mentioned above, with a 1/2 19 inch casing, dimensions of approximately 215 x 167 x 347 mm, and a weight of approximately 8 kg.

Interface and connection: 1 channel 4-20 mA analog output (maximum 750 Ω), 2 channels of alarm value signal and 1 channel of collective status signal digital output, supporting RS-485 or RS-232 interface (configurable).

Gas connection: The inlet and outlet ports are equipped with DN 4/6 hoses.

Power supply: Input voltage 85-250 VAC, 48-63 Hz, maximum power consumption of 40 VA.

Typical application scenarios

This series of analyzers is widely used, including but not limited to:

Heat treatment (CO, O ₂)

Combustion process (CO)

Biological fermentation tank (CO ₂, O ₂)