GE IS200HSLAH2A - BOARD (HSLA CARD) Along with ERAX card

GE IS200HSLAH2A - BOARD (HSLA CARD) Along with ERAX card

Part Number IS200HSLAH2A Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VI Function Module Availability In StockS200HSLAH2A is a High-speed Serial Link Interface Board for Host Application Boards manufactured by General Electric and is a part of the EX2100e regulator dual control system. The card is serially connected to the EX2100e ERAX M1 and M2 to UCSB CPU M1 and M2. 

The board has two jack inputs and outputs on its top surface. These are placed side by side along with one of the board's short edges. The board has two Halo TG 110-EO 50N5 transformers. Over twenty integrated circuits make up the board, including an FPGA (field-programmable gate array) at U1. There are two more (female) connectors on the bottom of the board. The FA/00 code is penned on the PCB. Multiple conduction sensors are integrated onto the card. IS200HSLAH2A CONTROL SOFTWARE The EX2100e control software provides high performance and aids in the understanding, installation, commissioning, tuning, and maintenance of the excitation control system by customers and field engineers. 

The exciter software is configured and loaded in the controllers using the ToolboxST application. On the ToolboxST Component Editor screen, the program is represented as control blocks that are coupled together to depict the signal flow. The software transducer system's output comprises the following: 1. The voltage of the generator 2. Current generated by the generator (average in phase with watts) 3. Reactive current generated by the generator (average in phase with reactive power, VARs) 4. The frequency of the generator (current) 5. Make a mistake (signal representing the change in the rotor speed) The output is used by the transducer system to calculate the following: 1. VARs and generator power 2. Generator flux magnitude (V/Hz) 3. Power factor and phase angleModule manufactured by General Electric as part of the Mark VI/VIe Series used in gas turbine sppedtronic control systems

The Series 90* -30 CPU374 PLUS provides a built-in enhanced Ethernet interface that  provides TCP/IP communications with: 

▪ Series 90, PACSystems, and VersaMax PLCs 

▪ Host computers running the Host Communications Toolkit or CIMPLICITY software 

▪ Computers running the TCP/IP version of the programming software CPU Features  

▪ High speed Boolean and non-Boolean processing provided by a 586-class 133MHz  processor 

▪ Two Ethernet ports: 10/100 Mbytes (one IP address) with a built-in, auto-sensing  Ethernet switch 

▪ Support for EZ Store Device allows you to download a program without a PC 

▪ 240KB of user memory Key Ethernet Features 

▪ Full PLC programming and configuration services 

▪ Periodic data exchange using Ethernet Global Data (EGD) and EGD commands to  read and write PLC and EGD exchange memory over the network 

▪ TCP/IP communication services using SRTP 

▪ Support for SRTP Client (Channels) 

▪ Modbus/TCP Server, supporting Modbus Conformance classes 0, 1, and 2. 

▪ Modbus/TCP Client, supporting Modbus Conformance classes 0, 1, and Function Codes 15, 22, 23, and 24 for Conformance class 2. 

▪ Remote PLC monitoring from a web browser 

▪ Comprehensive station management and diagnostic tools

Features 

Single-Slot Module 

SNP/SNP-X Protocol (master, slave) 

CCM Protocol (master, slave, peer) 

RTU Modbus Protocol (slave only) 

Supports connection to MS-DOS

 or Windows

 programming and configuration software package (monitor only) 

12 Mhz, 80C186 Microprocessor 

Two RS-422/RS-485 or RS-232 Serial Ports 

CCM, RTU and SNP/SNP-X Available on Either or Both Ports 

Simultaneous Communications on Both Ports (up to 9.6 Kbps, or 19.2 Kbps individually) 

High Performance Access to PLC Memory 

Three Status LEDs 

Reset pushbutton 

Soft Switch Configuration (no switches or jumpers) 

No Battery Required