GE DS200GDPAG1A Gate Driver Power Supply Board

GE DS200GDPAG1A Gate Driver Power Supply Board

Part Number DS200GDPAG1A Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark V Function Module Availability In StockThe DS200GDPAG1A is a high-frequency power supply board designed for the Mark V board series by General Electric. This 600 to 700 W board can accept both AC and DC supplied power supply once fitted. This card can be used to install and apply to a variety of GE drives and exciters. 

 The board may receive AC power ranging from 80 to 132 VAC. If the drive is powered by DC, the sources can range from 105 to 140 VDC. The DS200GDPAG1A gives the finest user experience thanks to a variety of integrated board features. A 120 VDC power supply, a 50 VAC output transformer, and a control power supply are among the features. Onboard are control signal level circuits as well as protective circuits. The key characteristics of this board are an input rectifier and filter, a regulator, and a 27 kHz inverter. All of the board's inputs are isolated, guaranteeing that there are no interruptions or voltage spikes. Users can check the status of the board using four onboard LEDs and two neon indicators. Installation and storage specifications specified by the manufacturer for both the board and the drive should be reviewed and followed. This set of instructions will ensure that the entire system runs smoothly.

Hardware Tips and Specifications

When installed, this 600 to 700 W board is capable of inputting both AC and DC sourced power supplies. This card can be installed and applied to a wide range of GE manufactured drives and exciters. AC power sourced to the board can measure between 80 and 132 VAC. Should DC power be inputted to the drive, sources can rate between 105 and 140 VDC. An array of integrated board features ensures that DS200GDPAG1A provides the best user experience. These features include a 120 VDC power supply, a 50 VAC output transformer, and a control power supply. 

Both control signal level circuits and protective circuits are found onboard as well. An input rectifier and filter, a regulator, and a 27 kHz inverter complete the main features of this board. All inputs on the board are isolated, ensuring no interruptions or voltage spikes. Four onboard LED and two neon indicators provide board status diagnostics to the users. Manufacturer provided installation and storage parameters for both the board and drive should be reviewed and followed. This instructions will ensure that the system as a whole operates properly. For a step by step guide to installing and wiring DS200GDPAG1A, please refer to the series manual as well as the datasheet. 

General Electric, the manufacturer, originally provided all Mark V boards with technical support. While generally defined above, the integrated circuits in the assembly of this DS200GDPAG1A product offering are actually described in detail in this DS200GDPAG1A PCB's factory-printed instructional manual available to the manuals tab above. As indicated in this instructional documentation, the DS200GDPAG1A High Frequency Power Supply's integrated circuits include:

The Inverter Overcurrent Circuit

The Regulator Overcurrent Circuit

The P80 Bus Overvoltage Circuit

The Control Voltage Undervoltage Circuit

The CVOK Running Signal Circuit

Instructions and warnings related to the operation of the product:

The following specifications must be strictly observed:

 The technical specifications and typical applications of the product system must be strictly observed.

 PERSONNEL TRAINING: Only trained personnel may install, operate, maintain or repair the product system. These personnel must be instructed on the

These personnel must be instructed and briefed on the conditions in the hazardous area.

 Unauthorised modifications: No modifications or structural changes may be made to the product system.

 Maintenance Responsibility: It must be ensured that the product system is used only under appropriate conditions and in a condition fully suitable for use.

 Working environment: The user must fulfil the specified environmental conditions:

Safety regulations

The following safety regulations must be fully observed when (maintenance) work is carried out on the product system:

1 Disconnect completely.

2 Secure to prevent reconnection.

3 Confirm that the installation has been completed.

4 Perform grounding and short-circuiting.