GE SELA36AT0030| General Electric | Circuit Breaker

GE SELA36AT0030| General Electric | Circuit Breaker

Product Description P/N: 531X133PRUAMG1 DESCRIPTION / SPECIFICATIONS Description The 531X133PRUAMG1 by General Electric is a Process Interface Board. Engineered for industrial applications, it facilitates seamless integration, monitoring, and control of processes. With GE's precision, this board ensures optimal performance and reliability in diverse industrial environments. Technical Specifications Brand General Electric Category Drives Part Number 531X133PRUAMG1 Subcategory Control/Interface Board Type PROCESS INTERFACE BOARD TERMINAL SCREW TERMINAL Information About 531X133PRUAMG1 The 531X133PRUAMG1 is a PCB board component made by GE. This PCB is designed for use within several general purpose drive systems from GE. Please refer to your particular system鈥檚 user guide or manual to ascertain compatibility. 

 The 531X133PRUAMG1 functions as a Process Interface Board. Interface components typically are used to amplify, isolate, filter, and convert their input signals into output signals that are suitable for their connected control systems. The PRUAM board is only one version of several available within this series. The 531X133PRUAMG1 is a square board with a single factory-made drill hole placed in each corner. The board carries the round GE logo, the board number, and codes like 92/38, 009/01, 002/01, 006/01, and F31X133PRUALG1. Codes may be located on the front or rear surfaces of the PCB. The 531X133PRUAMG1 has components that allow connection such as a three-position terminal strip. This is marked TACH + on one side and TACH - on the other. The board has two vertical pin cable connectors and a single 16-pin (vertical) header connector. The 531X133PRUAMG1 is populated by potentiometers (7,) resistor network arrays(5,) resistors (over 100,) diodes, and capacitors. 

Capacitors vary in the material used, but include aluminum electrolytic, polyester vinyl and capacitors made from ceramic material. The board has 15 jumper switches and several TP test points. It has a single switch component (marked 鈥淭ach Range,鈥? with seven individual toggles located on the switch. If more information about the board or its components is needed, this may be found through GE publications like user guides and manuals. Manufacturer information General Electric (GE) is a multinational conglomerate founded in 1892, based in the United States. It operates in various industries, including aviation, healthcare, renewable energy, and power. GE is known for its innovations in technology, manufacturing, and infrastructure solutions. 

 IQElectro is not an authorized distributor. QElectro LLC (IQElectro) is NOT an Authorized Distributor or in any way affiliated with Rockwell Automation, Siemens, or any other Manufacturers. IQElectro is NOT an Authorized Dealer of this product. The product may be of older version, date codes, or design than that available from authorized dealers. As IQElectro is not an authorized dealer of this product, the Original Manufacturer's Warranty and Support DO NOT apply.IQElectro sells SURPLUS onlyand DOES NOT SELL SOFTWARE or FIRMWARE licenses For more detailed information, please refer to the full version of our disclaimer policy Disclaimer Policy.

Features 

 Single-Slot Module 

 SNP/SNP-X Protocol (master, slave) 

 CCM Protocol (master, slave, peer) 

 RTU Modbus Protocol (slave only) 

 Supports connection to MS-DOS

 or Windows

 programming and configuration software package (monitor only) 

 12 Mhz, 80C186 Microprocessor 

 Two RS-422/RS-485 or RS-232 Serial Ports 

 CCM, RTU and SNP/SNP-X Available on Either or Both Ports 

 Simultaneous Communications on Both Ports (up to 9.6 Kbps, or 19.2 Kbps individually) 

 High Performance Access to PLC Memory 

 Three Status LEDs 

 Reset pushbutton 

 Soft Switch Configuration (no switches or jumpers) 

 No Battery Required