Westinghouse iGen series digital inverter generator

Other common configurations: hour meter (cumulative running time), waterproof interface (IP44 level), frame grounding terminal (can be grounded by an electrician).

2. Model specific configurations and parameter differences

Category iGen1200 iGen2200 iGen2500 iGen4500s

Engine parameters: displacement of 54cm ³, maximum speed of 5200rpm, oil capacity of 250mL, displacement of 79cm ³, maximum speed of 5300rpm, oil capacity of 350mL, displacement of 98cm ³, maximum speed of 5500rpm, oil capacity of 350mL, displacement of 224cm ³, maximum speed of 3600rpm, oil capacity of 600mL, including battery (sealed maintenance free)

Power parameters: continuous power 1000W, starting power 1200W, continuous power 1800W, starting power 2200W, continuous power 2200W, starting power 2500W, continuous power 3700W, starting power 4500W, including output power meter

Interface configuration: 1 x 240V AC (15A), 1 x 12V DC (5A, 60W), 1 x 5V USB (2.1A, 10W), 1 x 240V AC (15A), 1 x 5V USB (2.1A, 10W), 1 x 240V AC (15A), 1 x 5V USB (2.1A, 10W), 2 x 240V AC (15A), 1 x 12V DC (8A, 100W), 1 x 5V USB (2.1A, 10W)

Starting method: manual start, manual start, manual start+electric start+wireless remote control start (starting up to 50 meters and stopping at 25 meters)

Special configuration - Data center (cyclic display of accumulated running time, remaining running time, output power, fuel level, output voltage), telescopic handle+wheels (easy to move), fuel gauge

Dimensions and weight: length 463 x width 262 x height 395mm, dry weight 15kg, wet weight 17kg, length 500 x width 285 x height 450mm, dry weight 21kg, wet weight 24.5kg, length 500 x width 285 x height 450mm, dry weight 21.5kg, wet weight 25kg, length 650 x width 480 x height 520mm, dry weight 49.5kg, wet weight 60kg

3. Accessories list (included as standard with the box)

General accessories: SAE 10W-30 engine oil (250mL for iGen1200, 350mL for iGen2200/2500, 600mL for iGen4500s), fuel funnel, spark plug socket wrench, user manual.

Exclusive accessory: iGen4500s comes with an additional wireless remote key.

Complete operation process (detailed explanation by model)

1. Preparation before startup (applicable to all models)

Environmental inspection: Confirm that it is placed in a ventilated outdoor area, level and dry, with appropriate spacing and no flammable materials in close proximity.

Oil inspection:

Engine oil: The new engine has no engine oil and needs to be filled with SAE 10W-30 engine oil of the corresponding capacity according to the model (15W-40 can be replaced in high temperature environments). The oil level should be checked at the bottom edge of the oil filling port (starting too low can damage the engine).

Fuel: Add unleaded gasoline of grade 91 or above, do not overfill, and check for leaks after refueling.

Load disconnection: Ensure that all electrical appliances and tools are not connected to the generator interface or have turned off the power to avoid load shock during startup.

Other checks: Confirm that the spark plug cap is securely connected, the air filter is unobstructed, and the fuel cap vent is in the "ON" position (iGen1200/2200/2500).

2. Startup operation (by model)

(1) IGen1200 startup

Turn the fuel cap vent to the "ON" position.

Rotate the engine and fuel control switch counterclockwise to the "ON" position.

Cold engine start: Push the air damper lever to the right to the "START" position; Heat engine restart: Keep the throttle lever in the left "RUN" position.

Press and hold the device with one hand, and pull the starter rope with the other hand. Slowly pull until resistance is felt, then quickly pull it out with force. After starting, slowly release the rope (to avoid damaging the starter with a loud bounce).

After the engine starts, wait for it to warm up, gradually push the throttle lever to the left to the "RUN" position, and then connect the load.

(2) IGen2200/2500 startup

Turn the fuel cap vent to the "ON" position.

Cold engine start: Rotate the engine, fuel, and throttle control switches clockwise to the "CHOKE" position; Heat engine restart: Turn to the "ON" position.

Start the engine using the iGen1200 manual start method.

After the engine is warmed up, turn the control switch counterclockwise to the "ON" position and then connect the load.

(3) IGen4500s startup (three ways)

① Electric start

Turn the fuel control switch clockwise to the "ON" position.

Press and hold the engine control switch to the "START" position for 1 second, then release it and it will automatically pop to the "AUTO RUN" position. The electric starter will start the engine (if it fails to start once, the device will automatically retry).

Directly connect the load (no need to manually adjust the air door, the equipment comes with an automatic air door).

② Manually start

Ensure that the battery is connected (it cannot start when there is no power, and needs to be charged or replaced first).

Turn the fuel control switch to "ON" and push the engine control switch to the middle "AUTO RUN" position.