Westinghouse 2400i digital inverter generator

Westinghouse 2400i digital inverter generator

Detailed explanation of core product information

1. In depth analysis of technical parameters

Category parameter details note explanation

The engine system has a single cylinder four stroke overhead valve (OHV), and the air-cooled OHV design improves combustion efficiency and extends engine life; Air cooled structure simplifies maintenance and adapts to complex outdoor environments

Power parameters: displacement of 79cm ³, maximum speed of 5000rpm, intelligent adjustment of speed with load (operating at the lowest speed in ECO mode)

Oil specification: The oil capacity is 400mL. It is recommended to use SAE 15W-40 API SG grade for ambient temperatures greater than 40 ℃, and 10W-30 for temperatures ≤ 40 ℃; It is strictly prohibited to mix different types of engine oil

Unleaded gasoline (91 octane and above) for the fuel system, with an ethanol content of ≤ 10%. If the ethanol content in the 5.0L fuel tank is too high, it is easy to cause corrosion of the fuel system. It is recommended to prioritize the use of ethanol free gasoline; Under full fuel condition, ECO mode can run for 8-10 hours

AC output 240V/50Hz, continuous power 2100W, starting power 2400W pure sine wave output, total harmonic distortion<3%, suitable for sensitive equipment such as computers and precision instruments

DC output 12V, maximum current 8A, maximum power 100W. The output is non regulated to avoid connecting devices that are sensitive to voltage fluctuations (such as precision electronic devices)

The protection level of the socket is IP44, which can resist splashing water but cannot be exposed to rain or soaking

Physical characteristics: length 500mm x width 340mm x height 440mm, dry weight 20kg. The handle design is convenient for single person short distance transportation, and the wet weight includes the weight of engine oil and fuel

2. Complete analysis of control panel functions

Component Name Function Description Operation Points

240V AC 15A socket (2 sockets) outputs 240V AC power, with a maximum load of 2400W per socket. When inserting the plug, it needs to be fully pushed in and the waterproof cover should be closed after use

Press and hold the engine stop button to stop the engine. In emergency situations, it can be used directly. Normal shutdown requires disconnecting the load first and running without load for 1 minute before operation

After the reset button of the generator is overloaded or short circuited, after troubleshooting, it is necessary to ensure that the load does not exceed the standard before resetting the AC output, otherwise the protection will be triggered again

ECO throttle switch ON: energy-saving mode, OFF: standard mode. ECO mode is used for small loads (<1000W), and standard mode is used for large loads (>1500W) or inductive loads

Throttle knob START (cold start), RUN (hot run) After starting the cold engine, preheat the engine for 3-5 minutes before pushing it to the RUN position to avoid stuffiness

Multi functional VST instrument displays voltage, speed, and cumulative running time. Press the panel button to switch display modes, and the backlight can be illuminated in low light environments

Fuel control switch ON (run), OFF (stop) should be turned to OFF for long-term storage, and the machine should be stopped after running out of fuel

The low oil warning light (red) lights up when the oil level is too low, and the engine automatically shuts down. It needs to be refilled with oil to the standard level before restarting

Overload alarm light (red) lights up when the load exceeds the standard or short circuit occurs. To cut off the AC output, the load needs to be reduced or the short circuit fault needs to be eliminated before resetting

Output indicator light (green) lights up when the engine is running and the AC output is normal. The green light does not light up but the engine is running. It is necessary to troubleshoot the output fault

Connect the grounding terminal to the ground wire to enhance electrical safety. It is recommended to ground when outdoors in humid environments or when connecting metal enclosed equipment

12V DC socket outputs 12V DC power, compatible with cigarette lighter plug. Do not insert into car cigarette lighter (high temperature can easily cause fire)

3. Function and position of core components

Air filter: located on the right side of the body, filters dust from the intake air to prevent engine cylinder wear; Regular cleaning is required, and the cycle should be shortened in dusty environments.

Spark plug: located on the left side of the body, it generates an electric spark to ignite the fuel mixture; Carbon deposition or wear can cause difficulty in starting and unstable operation.

Spark arrester: installed at the outlet of the muffler to prevent sparks from escaping and causing fires; When used in outdoor or dry environments, it is necessary to ensure cleanliness and smoothness.

Fuel filter: located below the fuel inlet inside the fuel tank, filters impurities in the fuel to avoid clogging the fuel injectors.

Oil inspection cover: on the left side of the body, open to check or add oil; The oil filling port is threaded, so avoid over tightening and damaging the threads when tightening.