GE IS200DSPXH1C Digital Signal Processor Control Board

GE IS200DSPXH1C Digital Signal Processor Control Board

Part Number IS200DSPXH1C Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series EX 2100e Function Module Availability In StockIS200DSPXH1C functions as Digital Signal Processor Control Board developed by GE. It is the primary controller for the bridge, motor regulator, and gating functions in Innovation Series drives. Specialized Hardware Functions Custom logic in Field Programmable Gate Arrays (FPGA) or ASICs with supporting circuits is used to provide specialized functions on the DSPX board. ASICs contain the majority of specialized and support functions. 

 P1 has four serial interfaces, which are as follows: Two 5 Mb/s ISBusTM interfaces that can be used as master or slave One asynchronous TTL interface for a computer-based configuration tool, with RX, TX, and TXEN/RTS data signals One asynchronous TTL interface to a programmer board, including data signals RX, TX, and RTS Synchronizing load pulse signals accomplishes the following tasks: An inner loop load pulse signal records I/O values such as bridge, motor, or generator voltages and currents, as well as VCOs, tachometer counters, and discrete inputs. It can also synchronize ISBus channels, software, and bridge gating outputs. An application loop load pulse signal is used to capture values of other application VCOs and optionally the tachs at a sub-multiple or multiple of the inner loop load pulse. Onboard Firmware Flash memory stores onboard firmware. 

There are three major kinds: The boot loader is in charge of the power-on sequence and should not be reloaded in the field. The specific control functions for the drive or exciter product are defined by application code. This code is loaded via the exciter's Tool port, and configuration parameters are loaded via the toolbox. The Unit Data Highway is used to load exciter parameters. If applicable, drive parameters are loaded to ACL_ via serial port, ISBus, or Ethernet. Indicating Lights DS1: Fault LED driven by the DSP, ON or flashing: A fault has occurred or during reset, OFF: No faults are present DS2: Status monitor LED driven by the DSP, Flashing: Running, ON: Stopped, OFF: A fault has occurred or during reset I/O Definitions The DSPX includes three I/O connectors as follows: P1 backplane connector P5 DSP emulator port P6 engineering monitor port The P1 connector provides memory mapped process bus address space as well as four chip select signals to support bridge and customer input/output (I/O) interfaces.

It also includes controls for a standard UART serial interface to a programmer board and a configuration tool, as well as two additional ISBus proprietary serial interfaces for ACL or local expansion functions. The P5 emulator port (on the board's front panel) connects to the TI emulator port. It includes a scan interface (similar to JTAG) for emulation and FLASH programming. The P6 engineering monitor port (located on the board's front panel) connects to the DSP synchronous serial port and allows only GE engineering users to connect to a terminal. Handling Precautions Static-sensitive components may be found on printed wiring boards. As a result, WOC packages all replacement boards in anti-static bags. When handling boards, follow the following guidelines: Anti-static bags or boxes should be used to store boards. When handling boards or board components, use a grounding strap.

SPECIFICATIONS:

Part Number: IS200DSPXH1C
Manufacturer: General Electric
Series: EX2100
Product Type: Digital Signal Processor Control Board
Number of channels: 12
Input span: 4-20 mA
Technology: Surface Mount
Common Mode Voltage Range: ±5 V
Maximum Lead Resistance: 15Ω
Analog output current: 0-20 mA
Operating temperature: -30 to 65 °C
Size: 8.26 cm high x 4.19 cm
Repair: 3-7 Day
Availability: In Stock
Country of Origin: United States
Manual: GEI-100267B

Our Main Brands

· - ABB Advant-800xA，Advant OCS，Bailey Infi 90 and Net 90，H&B Freelance 2000，DSQC Robots，IGCT / IGBT

· - GE General Electric Field Control, Genius I/O, QuickPanel, RX3i PacSystem, Series 90, Series 90, Series VersaMax

· - Allen Bradley Allen-Bradley SLC500, MicroLogix, CompactLogix, ControlLogix, PLC-5, Panel View,

· - Bently Nevada 3300 System, 3500 System

· - Honeywell 7800 Series, FSC, IPC, Mxopen, TDC 2000, TDC 3000, Experion PKS(C200,C300)

· - Yokogawa Centum CS - Centum VP, Centum XL - micro XL, FA-M3, ProSafe-PLC

· - Ovation, Foxboro, EPRO, Emerson DeltaV, Fuji, Siemens, HIMA, Prosoft, Invensys Triconex, ICS TRIPLEX, Woodward, Bachmann, Schneider