The CSH01.1C-PB-ENS-NNN-MA1-S2-S-NN-FW, identified by part number R911329829, is a control section within the Rexroth IndraDrive CSH Advanced Controllers series. It is engineered for single-axis servo control in industrial automation environments where deterministic communication, flexible feedback evaluation, and integrated safety functions are required. The control section clips into an IndraDrive servo inverter and assumes responsibility for motion command interpretation, encoder processing, analog signal handling, and safety state management, leaving the power section to perform the actual current conversion.
The PB segment of the type code specifies PROFIBUS-DP as the field communication interface. PROFIBUS-DP provides cyclic exchange of process data, including command values, status words, and drive parameters, between the control section and a higher-level PLC or motion controller. The interface supports the deterministic behavior expected in motion control applications, with bus cycle times that determine the achievable position loop update rate. The control section also provides an RS-232 serial port for local parameter access and commissioning, offering a direct connection when fieldbus access is not available or when local diagnostics are required.
The PROFIBUS-DP interface positions this control section within plant architectures that already use PROFIBUS as the primary fieldbus. It does not provide native Ethernet-based real-time communication, so the drive’s role is defined by the cyclic data exchange model of PROFIBUS-DP. The control section therefore functions as a slave device on the PROFIBUS network, responding to commands from a master controller and returning feedback and diagnostic data.
The ENS segment in the type code identifies the encoder evaluation configuration. The control section supports a broad set of feedback formats: IndraDyn S motor encoders, 1 Vpp sinusoidal signals, Hiperface, EnDat 2.1, and 5 V TTL incremental encoders. This multi-format capability allows the same control section to be paired with different motor families and feedback device types without changing hardware. The encoder interface terminates on a 15-pin D-Sub female connector and supplies regulated power to the feedback device, including 12 V for sensors that require it. The independent encoder channel means that feedback processing does not require an additional external evaluation module.
The ability to accept both absolute and incremental feedback formats has practical consequences for machine design. Absolute encoders eliminate the need for homing sequences after power loss, while incremental encoders may be preferred in applications where cost or existing infrastructure dictates their use. The control section’s firmware recognizes the connected encoder type and configures the position and velocity feedback paths accordingly.
The MA1 segment denotes a multifunction module that adds two analog inputs and two analog outputs, each with 12-bit resolution. The channels operate on a bipolar ±10 V range, which is the conventional interface level for velocity and torque reference signals in industrial drive systems. The analog inputs can accept external setpoints from a supervisory controller, a potentiometer, or a signal conditioner, while the analog outputs can mirror internal drive variables for monitoring or for use by other equipment in the cabinet.
The analog signals are routed through a D-Sub 15 female connector. Two reference outputs source 5 V at 1 mA for external potentiometers, supporting legacy analog control schemes without requiring an additional power supply. The multifunction board is designed to maintain low power demand, limiting the additional thermal load inside the drive enclosure. This analog interface complements the PROFIBUS-DP digital communication path, providing a parallel hardwired channel that remains available when the fieldbus is not exchanging data or when a simple analog reference is preferred.
The S2 segment in the type code corresponds to Safe Motion functionality. Safe Motion extends beyond basic Safe Torque Off by supporting monitored stop and limited-speed functions within the drive itself, without relying on external safety relays for every stop category. The safety functions are integrated into the control section and act on the drive’s power devices. In multi-axis systems, the control section can distribute safety states across axes and report diagnostic information to the higher-level control system, centralizing motion-related safety logic within the drive platform.
The FW suffix indicates that firmware is factory-loaded, ensuring that the control section is delivered with the appropriate motion control software. When installed in an IndraDrive inverter, the CSH01.1C-PB-ENS-NNN-MA1-S2-S-NN-FW coordinates position, velocity, and torque control loops, manages the PROFIBUS-DP data exchange, processes encoder feedback, and enforces the configured safety functions. Its role is that of a motion and safety bridge between the machine control level and the power conversion stage.



