ABB 086348-001 Step linear control board bargaining

LED Displays

Power

Green Internal supply voltage is available

Failure

Off Normal status

Orange Self test

Flashing orange Overtemperature occurred during operation

Red Hardware failure of the basic unit

Flashing red Software failure of the system

Run/Stop

Green Processing active

Flashing green Process was stopped and is now started

again

Red Processing inactive

Flashing red Process was active and is stopped now

Orange Self test

Off Software initialization

Prim/Sec In case of redundancy please see the

LED’s meaning in manual “Mounting and

Installation Instruction”.

For not redundancy the states are:

Orange Self test

Off Normal status

Operator Controls

Run/Stop switch Connected to LED

Toggle Prim/Sec For redundancy.

Toggles between primary and secondary

AC 800F (operational on primary AC 800F

only, and only if a secondary AC 800F is

available)

Reset Reset button

press and hold > 4 s for coldstart

Front Panel Connections

Power supply Two connectors for 24 V DC,

automatic input selection when used with

single power supply

Diag For diagnostics and optional radiocontrolled

clock

9-pin male connector

Fig. SD 802F

Power Supply SD 802F / SD 812F

Technical Data SD 802F

Input voltage 2 x direct current 24 V DC

permissible range 19.2 - 32.5 V DC

Input current at

nominal load 1.3 A at 24 V DC

Rated input power 31 W

Backup energy for

the event of

power failure > 20 ms

Fuse For each supply: subminiature fuse

3.15 AT, soldered

Output voltage 3.3 V DC (± 3%) typical

5 V DC (± 3%) typical

Output current 0.5 - 5 A

Current limit approx. 6 A

Automatic return to normal operation after

short circuit

Total output power max. 26.5 W

Weight 0.460 kg

Technical Data SD 812F

Input voltage 2 x direct current 24 V DC

permissible range 19.2 - 32.5 V DC

Input current at

nominal load 1.7 A at 24 V DC

Rated input power 41 W

Backup energy for

the event of

power failure > 20 ms

Fuse For each supply: subminiature fuse

3.15 AT, soldered

Output voltage 3.3 V DC (± 3%) typical

5 V DC (± 3%) typical

Output current 0.5 - 6.5 A to 3.3 V

0.5 - 5.5 A to 5.0 V

Current limit approx. 7.5 A

Automatic return to normal operation after

short circuit

Total output power max. 35 W

Weight 0.460 kg

Technical Data

Rated voltage 3.3 V / 5 V, ±3%, from CPU board

Power consumption max. 2.8 W

Thin Ethernet 10Base2

RAM and real-time-clock buffering time

PM 802F PM 803F

New battery inserted ≥ 1,5 years without buffering

After “Low” warning ≥ 10 days

Battery 3.6 V lithium battery, 950 mAh

(not in the delivery)

Weight approx. 0.150 kg (without battery)

June

Description

These communication modules provide Ethernet communications

to the system bus compliant with IEEE802.3 standard.

Communications module, to connect a commercial transceiver

with AUI connector (15-pin female plug DIN 41652).

LED Displays

State

Off No supply voltage, module is isolated

Green Power supply on, module identified and

ready to operate as configured.

Orange Power supply on,

module identified and either:

— normal transitory state after module

startup

— configuration mode of Boot Loader

Orange flashing Power supply on, module identified; module

not connected to proper bus structure.

Red Power supply on and either:

— module not yet identified (normal for

short time during module startup)

— error occurred during module test

Battery (PM803F)

Off AC 800F is active, EI 812F not active

=>buffering from power supply module

AC 800F is off (no watchdog of the batteries

voltage) =>buffering from battery.

Orange During battery recovery or start-up phase

Red Warning: battery low, no battery inserted,

insufficient electrical contact etc.

Green battery inserted and data protection provided.

Battery (PM802F)

Off Sufficient buffer battery voltage