Bristol Babcock Control Wave Micro 396563-07-4 CPU33 240mA @ 3.3VDC

Bristol Babcock Control Wave Micro 396563-07-4 CPU33 240mA @ 3.3VDC

CAUTION

When installing units in a hazardous area, make sure all installation components  selected are labeled for use in such areas. 

Installation and maintenance must be performed only when the area is known to be 

non-hazardous. 

Installation in a hazardous  area could result in personal injury or property damage. 

Always turn off the power to the ControlWave Micro before you attempt any type of wiring. 

Wiring of powered equipment could result in personal injury or property damage. 

To avoid circuit damage when working inside the unit, use appropriate electrostatic 

discharge precautions, such as wearing a  grounded wrist strap. 

Do not open enclosure unless area is known to be non hazardous. 

SPECIFICATIONS: ControlWave Micro 

POWER  

External Power Input: 10.7 to 30 V dc (+12 V dc) or 

21.7 to 30 V dc (+24 V dc), depending on configuration of jumpers switches, reverse polarity protection. 

Input: 10.7 to 30 V dc, 3A max, 36 watts max. 

Reference ratings for each device are: 

396560-01-6:  2 mA @ 3.3 V dc 

396560-02-4:  2 mA @ 3.3 V dc 

396563-16-3:  240 mA @ 3.3 V dc  

396581-06-4:  145 mA @ 3.3 V dc 

396657-02-8:  2A @ 24 V dc 

4A @ 12 V dc 

396686-01-0:  96 mA @ 120 V ac 

40 mA@ 3.3 V dc 

396897-02-9:  46 mA @ 3.3 V dc 

24.3 mA @ Vext (11-30 V dc) 

ENVIRONMENTAL  

Operating Ambient Temperature: —40 to +70C. 

Storage Temperature:  —40 to +85C. 

Operating Humidity:  15 to 95%, non-condensing. 

WEIGHT ;0.36 kg (4-slot base unit or 4-slot expansion unit).  

APPROVALS:ATEX/IECEx 

ControlWave Micro Special Conditions for Safe Use 

Connections made to RS-232 or RS-485 communications ports shall be mechanically secured in place with suitable screw connections to prevent loosening or disconnection during use.  

When using Ethernet connections, the RJ45 (Ethernet) connection must have a mating 

connector with a valid securing clip to prevent loosening or disconnection during use.  

The USB connector on the IEC 62591 module shall not be used unless the area is known to be nonhazardous (non-flammable). 

Install the ControlWave Micro within a suitable certified tool-accessible ATEX or IECEx approved IP54 or better enclosure.  

The area in which the equipment is used should be  a minimum of Pollution degree 2, as defined by  IEC 60664-1 (that is, the environment should not contain conductive pollution and the equipment shall be installed in an indoor or sheltered location).  

The equipment may be used in zone 2 with flammable gases.  

The equipment may be used in the presence of  flammable gases and vapors with apparatus groups IIC or IIB or IIA and with temperature classes T1 or T2 or T3 or T4.  

The equipment is certified for use in ambient temperatures in the range of —40C ≤ Tamb ≤ +70C and should not be used outside this range.  

The equipment is to be installed by suitably trained personnel in accordance with theapplicable code of practice (typically IEC EN 

60079-14). 

The equipment does not require assembly or dismantling.  

With regard to safety it is not necessary to check for correct operation.  

No user adjustment is required.