ADLINK MVP-6200 Industrial Control Computer: PCIe Gen4 and PCI Hybrid Expansion

Internal expansion: Three M.2 channels and dual SIM cards

The motherboard provides rich expansion and debugging interfaces internally (see Figure 3-11/3-12):

M.2 Socket 1（Key E，2230）：PCIe Gen3 x1， Used for WiFi/BT modules.

M.2 Socket 2（Key B，3052/3042）：PCIe Gen3 x1 + USB3， Support 5G modules and achieve operator redundancy with two Micro SIM card slots.

M.2 Socket 3（Key M，2280）：PCIe Gen3 x4， Supports NVMe SSD, providing ultimate storage performance.

In addition, the onboard 2 x SATA III 6Gb/s (optional 3rd SATA) can accommodate 2.5 "HDD/SSD. It also provides USB 2.0 Type-A (dongle), 12V PWM fan connector, two I ² C buses (3.3V/5V level), external PWR/RESET pin, and 12V power pin (to power the AFM MxM onboard). The debugging interface includes DB40 and COM5/6 pin headers.

Detailed Hardware Installation Guide (Graphic and Text Steps)

The manual provides a large number of illustrations to introduce the installation of key components, which on-site engineers can use to operate:

1. Install 2.5 "SSD (two ways)

Method 1 (9.5mm thickness): Remove the top cover (loosen the screws), unscrew the 4 screws on the rear panel, remove the SSD tray, fix up to 2 SSDs with M3 screws, insert the SATA connector, and restore.

Method 2 (15mm thickness): Use the attached bracket and long/short SATA data/power cables. First, fix the SSD on the bracket and connect the cables. Then, install the bracket as a whole into the chassis and fix it with side panel screws. Finally, connect the motherboard SATA interface.

2. Install SODIMM memory

Remove the top cover, paste the attached thermal pad at the corresponding position on the motherboard (to avoid contact with the pins), and insert the memory module. Supports dual channels, recommended for paired installation.

3. Install WiFi module (Key E)

Remove the top cover, insert it into the M.2 E key slot, and secure it with M3 screws.

4. Install 5G module (Key B)

Pre install M2.5 bolts according to the module size (3042 or 3052), paste the thermal pad, insert the module and lock it with M2 screws, and install the Micro SIM card.

5. Install fan kit (optional)

Remove the top cover, connect the fan connector to the motherboard, and then secure the fan assembly inside the chassis.

6. Wall mounted installation (rear or side)

Provide two installation directions for wall brackets: rear installation (standard) or side installation (saving depth space). All are fixed with 6 M4 screws, and the installation hole spacing refers to the mechanical dimension diagram.

BIOS settings key items (for performance and compatibility tuning)

MVP-6200 is based on Aptio UEFI and can be accessed by pressing Del on startup and F7 on the boot menu. The following are the key settings:

1. CPU and Power Management (Advanced → CPU Configuration/Power Management)

Hyper Reading: It is recommended to enable (Windows/Linux optimization).

Active Performance cores/Efficient cores: The number of P cores (performance cores) and E cores (energy efficiency cores) can be manually controlled for power consumption or compatibility tuning.

Intel Virtualization Technology&Trusted Execution: Supports virtual machines and trusted execution when enabled.

SpeedStep/Speed Shift: Allow dynamic frequency modulation.

C States: Allow the CPU to enter a low-power state, saving energy.

TCC Activation Offset: Adjust the triggering temperature of overheating protection (0~63) to adapt to different heat dissipation environments.

State After G3: Set the power on behavior after power failure recovery (Last State/Always On/Always Off).

RTC Wake: timed wake-up function.

PCIe Wake: Allow PCIe devices to wake up the system.

2. Serial port mode and onboard device configuration

COM1/COM2 is independently set as RS232/422/485.

Three 2.5GbE ports can be independently enabled/disabled.

3. Hardware Monitoring and Fan Control (NCT6126D HW Monitor)

Real time display of CPU temperature, motherboard temperature, system fan and backplane fan speed and voltage. Fan control mode:

Manual: Fixed PWM duty cycle (0~255)

Auto: Automatic speed regulation

SMART FAN IV: Customize Four Temperature Speed Curves

4. BIOS Watchdog

After activation, the POST phase starts the watchdog and automatically resets upon timeout to prevent startup freezing.

5. Storage and VMD configuration (Chipset → SATA/VMD)

SATA mode can be selected as AHCI or RAID (R680E supports RAID 0/1/5/10).

VMD (Volume Management Device) supports Intel Optane Memory and RAID management.

M. 2 SATA channels can be independently enabled/disabled.

6. Backplane PCIe Configuration (Chipset → Backplane PCIe Configuration)

The maximum link speed (Auto/Gen1/Gen2/Gen3/Gen4), device detection timeout (100~65535ms), and PERST signal effective minimum/maximum time for each PCIe slot can be configured separately to be compatible with expansion cards from different manufacturers and avoid recognition failures.

Watchdog Timer (WDT) and Digital I/O (DIO) Development Library

WDT programming

Based on NCT6126D (eSPI interface), provide Windows API and Linux register examples.

InitWDT(), SetWDT (tick, unit) (tick 1~60, unit=0 seconds/1 minute) StartWDT()、ResetWDT()、StopWDT()。

The Linux example directly operates the 0x4E/0x4F registers, configures logical device 8, sets timeout values and units, starts and feeds the dog.