ABB Panel 800 Version 6 PP885 Hardware and Installation

1GB of memory (DDR2)

One multi-color indicator light (on-chip integrated)

Lithium battery, model BR 2032 (or CR 2032)

Power consumption 24W

Power input 3.15A slow melting,+24V DC (18-32V DC)

Power compliance CE: The power supply must comply with the requirements of IEC 60950 and IEC 61558-2-4 standards; UL and cUL: The power supply must meet the requirements of Class 2 power supply

Display TFT-LCD with LED backlight, resolution 1280 × 800 pixels, 262k colors

Display performance: brightness of 450cd/m ², horizontal viewing angle of 160 °, vertical viewing angle of 140 °

Backlight lifespan of 50000 hours

Display screen size 331.2 × 207.0mm

Working temperature range -10 ° C to+50 ° C

Storage temperature range -20 ° C to+70 ° C

Working humidity range 5% -85% (no condensation)

CE certification complies with EMC Directive 2004/108/EC+A1:2011

Chemical resistance

（1） Metal casing

Powder coating has almost no or no resistance to the following chemicals at room temperature: concentrated acetic acid, toluene, 30% nitric acid, and 97 octane unleaded gasoline.

（2） Touch screen and covering material

Autoflex EBA 180L: Not tolerant to high-pressure steam above 100 ° C, nor to various chemical substances (specific substance and contact time requirements: some substances may have adverse effects after 10 minutes of contact, please refer to the detailed list in the manual).

Touch screen surface: After exposure to solvents such as toluene, there is no visible change on the touch screen surface of the operation panel (refer to the manual for a detailed solvent list).

Touch screen protective film: It is recommended to use Autoflex EBA 180L protective film (model RX885/893, can be ordered from ABB), and its chemical resistance is detailed in the "Autoflex EBA 180L" section; Like all polyester based films, Autoflex EBA 180L is not suitable for long-term exposure to direct sunlight; The layered structure of the touch screen contains air, and in rare cases, bubbles may appear, which only affect the appearance and not the function, and may occur under specific environmental conditions.

Operation panel drawing

（1） Connector

The drawings indicate the positions of connectors and related interfaces (such as COM1/2, LAN, USB, C LAN, COM3/4, etc.), but COM4 is not supported on TxB SoftControl and TxB SoftMotion that include EtherCAT functionality. For detailed interface layout and pin definitions, please refer to the illustrations in the manual.

（2） Communication port

Port function and connection: The communication port supports protocols such as RS232, RS422, RS485, etc. Some port pins are defined as follows (example): RS232 TxD, RS422 Rx+, GND, RS422 Tx -, RS485 Tx -/Rx -, etc. (detailed pin allocation reference manual diagram); COM4 is not supported on specific models.

Special connection requirements: If two communication ports need to be used on the same physical port, Y-shaped distribution cable TK860V001 (part number 3BSE069476R1) must be used.

（3） PP885 contour

The contour diagram indicates the key dimensions of the operation panel (unit: mm), such as 286mm (partial length), maximum 8mm (related to installation plate thickness), 54mm (partial height), 268mm (partial length), 392mm (partial length), 410mm (overall length), etc. For detailed dimensions, please refer to the contour diagram in the manual.

（4） Environmental temperature

Temperature influencing factors: The maximum ambient temperature of the operation panel is specified in the specifications. Here, the ambient temperature refers to the temperature at which the electronic components of the operation panel are cooled inside the equipment cabinet; In most cases, the ambient temperature of the control panel is much higher than that of the equipment cabinet; If the cabinet is high and contains multiple heating devices, the temperature at the top of the cabinet will be much higher than the expected temperature rise. All electronic devices are sensitive to heat, and the lifespan of electrolytic capacitors will be reduced by half with an increase of 8-10 ° C in temperature, and by a quarter with an increase of 15-20 ° C, and so on.

Temperature control suggestion: Rittal provides a solution for estimating the expected average temperature of the cabinet and various cabinet temperature control systems; The radiant heat value of enamel steel cabinets is 5.5W/(m ² ·° C); Installing fans inside the cabinet can make the temperature uniform, and the cooling effect of flowing air is much better than that of static air; The fan should be installed in a cooler area to blow cold air towards the control panel. If the fan is installed at the top and draws heat absorbing air upwards, it will cause the ambient temperature of the fan to rise and shorten its lifespan; The net power consumption of the operation panel can be estimated by multiplying the power supply voltage by the operating current of the operation panel (assuming that all power supply is converted into heat).

（5） Security

Power supply safety: Most operation panels are powered by 24V DC; If using a power supply that meets safety standards and only supplies power to the operation panel, there are no safety issues; If a 24V power supply is supplying power to other devices at the same time, caution should be taken. In the event of a potential short circuit between 230V AC and 24V DC on the control panel, insulation that meets safety requirements is not available. Assuming that 24V power supply is safe (such as SELV that complies with EN 60950 (anti electric shock) and UL 950 standards).