GE DS200LDCCH1ALA LAN Communications Board

GE DS200LDCCH1ALA LAN Communications Board

Part Number DS200LDCCH1ALA Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VIe Function Module Availability In StockIS420UCSBH4A Module manufactured by General Electric as part of the Mark VI/VIe Series used in gas turbine sppedtronic control systems View More IS220PSCAH1B Module manufactured by General Electric as part of the Mark VI/VIe Series used in gas turbine sppedtronic control systems View More IS220PDIAH1B Module manufactured by General Electric as part of the Mark VI/VIe Series used in gas turbine sppedtronic control systems.

General Electric manufactured the DS200LDCCH1ALA board as a drive control and local area network (LAN) communications card. This card was developed as a member of the Mark V Turbine Control System series of drive boards. The Mark V Series that this DS200LDCCH1ALA PCB was originally manufactured for has specific applications in the control and management systems of compatible and popular wind, gas, and steam turbine automated drive assemblies, as referenced in the full extended series name previously mentioned. This DS200LDCCH1ALA PCB's greater Mark V Series, while pertinent to some newly-developed alternative energy applications, still has to be considered obsolete as a whole, as it exists as a legacy product series discontinued for manufacture due to a manufacturer-identified functional series obsolescence. This DS200LDCCH1ALA LAN Communications/Drive Control Card's greater Mark V Series is still something of a highly-sought GE product series, as it exists as one of the final-developed product series to make use of the patented Speedtronic control system technology first seen with the release of the initial Mark I Series in the later 1960s.

Hardware Tips and Specifications

Drives across the DIRECTO-MATIC 2000 series are developed to have this card installed in its drive cabinet. An array of functions are provided by this board, such as device, motor, and I/O control functions. This drive control and LAN communications board features four microprocessors to filter card signals. Digital and analog I/O sent to the board is received and filtered with the onboard drive control processor (DCP). LAN systems fed to the drive are filtered through the LAN control processor (LCP) found on board. The remaining two processors, the motor control processor (MCP) and the co-motor processor (CMP), work in tandem with each other. The MCP provides the initial processing space for digital I/O communications. Should the calculations needed by the signal exceed the space power provided by the MCP, the CMP will supplement the processing power. The board is completed with an attachable alphanumeric keypad. Products purchased through AX Control will be shipped in a protective static resistant plastic bag. The board should only be removed once all manufacturer provided installation parameters have been reviewed. Refer to the series manual and the device datasheet for a complete guide to wiring and installing the DS200LDCCH1ALA board. Members of the Mark V series, including this drive control LAN communications card, were provided with technical support by General Electric. According to these originally-produced instructional manual materials, this DS200LDCCH1ALA PCB's I/O processing is achieved through the use of one of the following bus systems:

The DLAN+ LAN Protocol Bus System

The DLAN Smaller and Early Larger Drives LAN Protocol

The Genius Interface Board Bus System

The CPL Interface Board Serial Link Bus System

The C-Bus Interface Board Differential Bus System

Instructions and warnings related to the operation of the product:

The following specifications must be strictly observed:

 The technical specifications and typical applications of the product system must be strictly observed.

 PERSONNEL TRAINING: Only trained personnel may install, operate, maintain or repair the product system. These personnel must be instructed on the

These personnel must be instructed and briefed on the conditions in the hazardous area.

 Unauthorised modifications: No modifications or structural changes may be made to the product system.

 Maintenance Responsibility: It must be ensured that the product system is used only under appropriate conditions and in a condition fully suitable for use.

 Working environment: The user must fulfil the specified environmental conditions:

Safety regulations

The following safety regulations must be fully observed when (maintenance) work is carried out on the product system:

1 Disconnect completely.

2 Secure to prevent reconnection.

3 Confirm that the installation has been completed.

4 Perform grounding and short-circuiting.