GE IS200EPCTG1A Exciter PT/CT Terminal Board

GE IS200EPCTG1A Exciter PT/CT Terminal Board

Part Number IS200EPCTG1A Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series EX 2100e Function Module Availability In StockIS200EPCTG1A is a Simplex Servo I/O Terminal Board manufactured and designed by General Electric as part of the EX2100 Series used in the GE Excitation Control System. The IS200EPCT Exciter PT/CT (EPCT) terminal board contains isolation transformers for critical generator voltage and current measurements. Two 3-phase generator potential transformer (PT) voltage inputs are input to EPCT as shown in the following diagram, EPCT Terminal Board. Two generators' current transformer (CT) inputs, with current levels of 1 A or 5 A, are input. 

All the isolation transformer output signals are cabled to the EMIO board in the control rack. In addition, one analog input, which can be either a voltage or current, is brought into EPCT. When the highest reliability is required, three EPCT boards can be used. GENERATOR VOLTAGE MEASUREMENT: Switches are used to wire TB1 with the generating voltages from the customer's potential transformers. The #12 AWG wire used in the cables has a maximum length of 1000 feet. 

The PT inputs are fused and have a rated voltage of 115 V rms at 50/60 Hz. On EPCT, two isolation transformers create a three-wire open delta voltage measurement, producing 1.533 V rms for a 115 V rms input. GENERATOR CURRENT MEASUREMENT: Switches are utilized to connect TB1 to the producing voltages coming from the potential transformers belonging to the client. The maximum length of the #12 AWG wire utilized in the cables is 1000 feet. The PT inputs have a rated voltage of 115 V rms at 50/60 Hz and are fused. For a 115 V rms input, EPCT uses two isolation transformers to provide a three-wire open delta voltage measurement that is 1.533 V rms. 

 ANALOG INPUT: With a voltage range of 10 V dc or a current range of 420 mA, EPCT may accept one non-isolated analog input. A maximum two-way cable resistance of 15 ohms is allowed for cables up to 300 meters in length. With the jumper JP1, the input type is chosen. Connectors J305, J308, and J315 receive the voltage signal after being spread out. APPLICATION DATA: The following, EPCT Board Layout, displays the EPCT board's layout. The voltage and current isolation transformers are designated as T1 through T6. Two screws hold down the removable terminal block TB1 and allow for its removal. As a safeguard against a CT open circuit state, terminal blocks TB2 and TB3 cannot be removed. In a simplex control, the voltage signals are transmitted to the EMIO board in the M1 controller through the J305 connector. The signals are fanned to connections J305, J308, and J315 and routed to controllers M1, M2, and C in a redundant control. Eight voltage test points (TP1TP8) are provided by EPCT, one for each secondary side leg of the isolation transformers.

Technical specifications and performance

Voltage & Current: Specific voltage and current specifications may vary depending on application scenarios and customised requirements, but usually have multiple voltage and frequency adaptations to suit the power standards of different regions.

Durability and Safety: High-quality power interface boards are usually made of durable materials and equipped with safety devices such as fuses and circuit breakers to ensure long term reliability and stability while protecting the equipment and users.

Communication features: Some power interface boards may have communication interfaces that allow the device to communicate with a computer or other control system for remote monitoring and control.

Indicator Lights and Displays: Some power interface boards may be equipped with indicator lights for displaying information such as power status, connection status, etc., to facilitate troubleshooting and status monitoring by users.

Instructions and warnings related to the operation of the product:

The following specifications must be strictly observed:

 The technical specifications and typical applications of the product system must be strictly observed.

 PERSONNEL TRAINING: Only trained personnel may install, operate, maintain or repair the product system. These personnel must be instructed on the

These personnel must be instructed and briefed on the conditions in the hazardous area.

 Unauthorised modifications: No modifications or structural changes may be made to the product system.

 Maintenance Responsibility: It must be ensured that the product system is used only under appropriate conditions and in a condition fully suitable for use.

 Working environment: The user must fulfil the specified environmental conditions:

Safety regulations

The following safety regulations must be fully observed when (maintenance) work is carried out on the product system:

1 Disconnect completely.

2 Secure to prevent reconnection.

3 Confirm that the installation has been completed.

4 Perform grounding and short-circuiting.