S7-300 - Industrial Ethernet / PROFINET CP 343-1 Lean

1.1 Applications

The CP 343-Lean communication processor is designed to run in the SIMATIC S7-300 or SIMATIC C7 automation systems.

It allows the S7-300 to be connected to industrial Ethernet and supports PROFINET IO.

To integrate CP in a linear bus or ring network to connect other Ethernet devices or to use PROFINET

Media redundancy with integrated 2-port ERTEC with automatic crossover, auto-negotiation and auto-detection

Real-time switch.

1.2 Enhanced Functions

Abbreviation for CP 343-1 Lean module

The module abbreviations for CP 343-1 Lean used below (such as CX10) correspond to the last four characters in the middle of the order number.

Configuration firmware version V3.0 requires new features

To use the features listed below, you need the following STEP 7 version:

● STEP 7 V5.5 + Service Pack 2 + Hotfix 1 + HSP 1056

If STEP 7 Professional V11.0 SP2 is used, only the CP function of firmware version V2.2 can be configured.

CX10 feature enhancements from firmware version V2.6 to V3.0 - works with STEP 7 V5.5

Firmware version 3.0 modules can use the following new features:

● PROFINET IO's "Shared device" function

● Use the PROFIenergy function

This requires the following PROFIenergy for CP 343-1 in the "SIMATIC_NET_CP" library

The blocks are used in conjunction with the STEP 7 versions listed above:

- PE_Start_CP, PE_CMD_CP, PE_I_DEV_CP and ET 200S for PROFIenergy

Program block DS3_WRITE_CP of the power module.

- See Standard for supplementary blocks FC0 through FC8 for PROFIenergy response data

The Library.

Photo Note:

1) Industrial Ethernet connection (PROFINET interface) : 2 8-pin RJ45 jacks

2) Connect the power supply

3) Slider for setting the ground connection of the housing

1.3 Communication Services

CP supports the following communication services:

● PROFINET IO

PROFINET IO allows direct access to IO devices over industrial Ethernet.

- PROFINET I/O device

Integration of the SIMATIC S7-300 automation system with CP into intelligent PROFINET IO devices (I

Equipment).

- Shared device

In STEP 7 V5.5, each submodule of the CP (IO device) can be assigned a maximum of two PROFINET IO

The controller.

Note the PROFINET System Notes for configuring PROFINET IO using shared IO devices

For system information, see /13/ (page 71).

● S7 communication and PG/OP communication with the following functions:

- PG function (including routing)

- Operator Monitoring Function (HMI)

- Data exchange only on an S7 connection configured at one end, not using the S7300/C7300

The communication block on the server

● Open communication services with the following functions:

- SEND/RECEIVE interface ISOonTCP, TCP, and UDP connections

UDP frame buffering on CP can be disabled during configuration.

When necessary, this can obtain a shorter response time, i.e. UDP frames arrive with the CPU

The interval at which it is evaluated.

- Multicast over UDP

The multicast mode can be realized by selecting the appropriate IP address when configuring the connection.

- FETCH/WRITE services implemented via ISO-on-TCP connections and TCP connections (servers; Correspond to

S5 protocol)

The addressing mode of FETCH/WRITE access can be configured as S7 or S5 addressing mode.

- Supports LOCK and UNLOCK for the FETCH/WRITE service

1.4 Other Services

CP also offers the following additional services:

● Media Redundancy (MRP)

In an Ethernet network with a ring topology, CP supports the medium redundancy protocol MRP. Can be MRP

The role of the client is assigned to CP.

● Clock synchronization based on industrial Ethernet

Clock synchronization can be configured in the following modes:

- SIMATIC mode

CP receives MMS time messages and synchronizes its local time and CPU time.

Accuracy approx. +/ -1 SEC

You can choose whether to forward the clock or not. You can also select the forwarding direction (Station > LAN or LAN > Station).

or

- NTP (Network Time Protocol)

CP Periodically sends clock queries to the NTP server and synchronizes it with the local clock. You can optionally forward the clock to

The CPU.

Accuracy approx. +/ -1 SEC

● Use factory set MAC addresses for addressing

CP can be accessed with a default MAC address, allowing IP addresses to be assigned.

● SNMP Agent

CP Supports data query through SNMP (Simple Network Management Protocol) version V1. It will be according to MIB II

The standard, LLDP MIB, Automated System MIB, and MRP Monitoring MIB provide specific MIBs

The content of the object.

● Module access protection

To protect a module from accidental or unauthorized access, you can configure different levels of protection.

● IP configuration

For PROFINET interfaces, CP can be configured to assign IP

Address method and mode, subnet mask, and gateway address.

Except STEP

7, the connection configuration can also be assigned through the block interface in the user program (FB55: IP_CONFIG).

● Web Diagnostics

With Web diagnostics, you can use a Web browser to connect from CP to PG/PC

Read diagnostic data in the station.

This allows the diagnostic buffer of the smart module in the rack to be read.

Using the Integrated Update Center on the diagnostics page, you can download the new firmware version and the diagnostics buffer message text.

If you do not need this feature, you can disable it in the STEP 7 configuration and disable port 80.

● Connection diagnostics using AG_CNTEX blocks

Connections can be diagnosed using the AG_CNTEX block.

- If necessary, you can activate or disable the connection or start the re-establishment of the connection.

- Use the Ping function to check the reachability of the connection.

- You can find out which connection types are established for the SEND/RECEIVE interface.

1.5 CP acts as a Web server

Enable the Web server function

To use the Web server functionality of CP, enable the relevant options in the "Web" parameter group of the STEP 7 module properties.

Enable port 80 of CP.

If this feature is no longer needed, disable it. By default, the Web server feature is enabled.

Web diagnosis

CP provides Web server functionality so that users can perform access through a Web browser. CP provides HTML

Pages can be used for Web diagnostics. With Web diagnostics, you can use an Internet browser to connect from CP to

PG/PC station to read diagnostic data.

You can access Web diagnostics at:

http:\<CP's IP address >

Using the integrated Update Center on the diagnostics page, you can download new firmware versions as well as language files for the diagnostics buffer message text.