SIEMENS QFM31xx series air duct sensor

SIEMENS QFM31xx series air duct sensor

Product basic information

1. Product model

Covering sub models such as QFM3100 (basic version), QFM3160 (with display), QFM3171D (4-20mA output), etc., collectively referred to as the QFM31xx series, it provides high-precision measurement of air duct temperature and humidity.

2. Application scenarios

Sensors are suitable for ventilation and air conditioning systems with high requirements for temperature and humidity accuracy and response speed. Typical installation scenarios include:

Industrial scenarios: storage and production workshops in paper mills, textile factories, pharmaceutical factories, food factories, and electronic factories;

Special venues: laboratories, hospitals, computer data centers, indoor swimming pools, greenhouses;

Functional roles: Air supply/return control sensor, humidity limit sensor after steam humidifier, building automation system (BAS) access sensor.

Core technical characteristics of the product

1. Power supply and signal output

Category parameter content, key data

Supply voltage AC/DC dual compatible 24 Vac (± 20%, 50/60Hz); 13.5-35 Vdc

Low power consumption design<1 VA

Humidity output with two signal types: 0-10 Vdc (corresponding to 0-100% RH, maximum current 1mA); 4-20 mA (corresponding to 0-100% RH)

The temperature output range can be selected from 0-10 Vdc/4-20 mA, and the range can be selected through jumper wires (see Table 2)

Cable lengths are classified by wire diameter as 24 AWG (50m), 18 AWG (150m), and 16 AWG (300m)

2. Measurement performance (accuracy and response)

Measurement Type Accuracy Index Response Characteristics Remarks

± 2% RH at relative humidity of 23 ℃; temperature coefficient<0.05% RH/℃ Time constant of about 20s (in flowing air) Effective measurement range 0-95% RH (0-9.5V/4-19.2mA linear)

± 0.8 ℃ at a temperature of 15-35 ℃; -The time constant of ± 1.0 ℃ at 40-15 ℃/35-70 ℃ is about 20 seconds (in flowing air). The sensing element is NTC 10K Ω

3. Protection and environmental adaptability

Protection level: IP65 (NEMA 4), dustproof and water-resistant, suitable for humid air duct environments;

Work environment: Adapt to the air temperature inside the duct (consistent with the selected temperature range), humidity 0-100% RH;

Material compatibility: The shell is made of polycarbonate (impact resistant), the filter cap is made of the same material, and the overall silicon free design avoids polluting sensitive environments (such as electronic factories).

Mechanical Design and Installation Specification

1. Mechanical structure

Overall composition: consisting of a housing (base+detachable cover plate), a printed circuit board (PCB), wiring terminals, mounting flanges, and an immersion probe (including sensing elements and filter caps);

Shell design:

Base: Integrated wiring terminal and conduit clamping system (fixing flexible conduit), color RAL 7001 (silver gray);

Cover plate: Built in measurement circuit and jumper (range configuration), color RAL 7035 (light gray), fixed with screws;

Probe: Made of polycarbonate material (RAL 7001), the end sensing element is protected by a filter cap to prevent dust contamination.

2. Installation method and requirements

Key requirements for installation method and operation steps

Install flange (recommended) 1. Assemble the flange with the sensor; 2. Fix the flange to the air duct according to the required immersion length; 3. Insert the sensor and tighten it to adjust the immersion length as needed. The flange material is PA66 (black)

No installation flange 1. Use 4 mounting holes on the shell; 2. Directly screw the sensor onto the air duct using the maximum immersion length to ensure measurement representativeness

Special scenario (dew point offset) 1. Only fix the flange to the air duct wall; 2. Insert the sensor from the flange and clamp it tightly. It must be installed in the return air duct to avoid measurement deviation

Installation taboos:

Avoid probe impact: Sensing components are easily damaged by impact and should be handled gently during installation;

Distance between steam humidifiers: The minimum distance from the humidifier should be ≥ 3m (recommended ≤ 10m) to prevent sudden humidity changes from affecting accuracy;

Sealing protection: It is forbidden to remove the seal between the shell and the cover plate to prevent water vapor from entering and damaging the circuit.

Parameter configuration and debugging

1. Jumper configuration (on PCB, under cover)

The jumper has 6 pins and 1 jumper cap, which is used to select temperature range, display unit, and activate testing functions. The specific configuration is as follows:

Configure the parameters corresponding to the jumper position of the configuration function

Temperature range selection left (1) -31 ° F~95 ° F (-35 ℃~35 ℃)

Right position (3) -40 ° F~158 ° F (-40 ℃~70 ℃)

Display unit selection (with LCD model) vertical right position Celsius (℃, factory default)

Vertical left Fahrenheit (℉)

Test function activation level signal output specific values (such as 0V/10V, 4mA/20mA) for troubleshooting

2. Debugging steps

Wiring inspection: Confirm that the power and signal lines are connected correctly (refer to the terminal definition in Figure 2-6, for example, QFM3171 needs to ensure that G1/I1 is powered on, even if only temperature output is used);