DS3800DEPB1A1A | General Electric LCI Excitation Control Board Mark IV

DS3800DEPB1A1A | General Electric LCI Excitation Control Board Mark IV

Product Description P/N: DS3800DEPB1A1A DESCRIPTION / SPECIFICATIONS Description The DS3800DEPB1A1A is an LCI Excitation Control Board manufactured by General Electric for the Mark IV series. It is designed for use in industrial applications. The board features multiple integrated circuits and connectors. It is built to provide reliable excitation control within the Mark IV system. The DS3800DEPB1A1A lacks a faceplate and is equipped with various mounting holes to facilitate installation.

 It is essential for ensuring proper excitation control in turbine applications. Technical Specifications Condition New / Never Used Surplus Part Number DS3800DEPB1A1A Description LCI Excitation Control Board Manufacturer GE (General Electric) Series Mark IV Connectors 1 x 20-pin ribbon cable, 5 x 10-pin connectors Terminals 4 terminals for adding components Trimmer Resistors 2 trimmer resistors Information About DS3800DEPB1A1A The DS3800DEPB1A1A also features four terminals that can be used for adding additional components. 

Additionally, the board includes two trimmer resistors. The trimmer resistors allow for fine adjustments to the board's performance parameters. When handling the DS3800DEPB1A1A board, specific procedures must be followed to ensure the 20-pin ribbon cable is protected from damage. Initially, any 10-pin cables connected to the board should be disconnected and temporarily moved aside. Next, the 20-pin connector should be gently unplugged by grasping it with one hand. The four screws securing the board to the rack should then be removed while the board is held in place with the other hand. It is critical to avoid pulling on the board to disconnect the ribbon cable, as this could result in damage to the cable. 

 The physical dimensions of the DS3800DEPB1A1A board are six inches in length and two inches in height. The drive's interior is specifically designed to accommodate the installation of this board, providing a designated location for secure and proper fitting. Manufacturer information General Electric (GE) is a multinational conglomerate founded in 1892, based in the United States. It operates in various industries, including aviation, healthcare, renewable energy, and power. GE is known for its innovations in technology, manufacturing, and infrastructure solutions.

 IQElectro is not an authorized distributor. QElectro LLC (IQElectro) is NOT an Authorized Distributor or in any way affiliated with Rockwell Automation, Siemens, or any other Manufacturers. IQElectro is NOT an Authorized Dealer of this product. The product may be of older version, date codes, or design than that available from authorized dealers. As IQElectro is not an authorized dealer of this product, the Original Manufacturer's Warranty and Support DO NOT apply.IQElectro sells SURPLUS onlyand DOES NOT SELL SOFTWARE or FIRMWARE licenses For more detailed information, please refer to the full version of our disclaimer policy Disclaimer Policy.

Features 

▪ Contains 10 Mbytes of battery-backed user memory and 10 Mbytes of non-volatile flash user  memory. 

▪ Provides access to bulk memory via reference table %W. 

▪ Configurable data and program memory. 

▪ Programming in Ladder Diagram, C, Structured Text, and Function Block Diagram. 

▪ Supports auto-located Symbolic Variables that can use any amount of user memory. 

▪ Reference table sizes include 32Kbits for discrete %I and %Q and up to 32K words each for  analog %AI and %AQ. 

▪ Supports Series 90-70 discrete and analog I/O, communications, and other modules. For a  list of modules supported, refer to the PACSystems RX7i Installation Manual, GFK-2223. 

▪ Supports all VME modules supported by Series 90-70. 

▪ Supports RX7i data monitoring over the web. Allows a combined total of up to 16 web server  and FTP connections. 

▪ Supports up to 512 program blocks. Maximum size for a block is 128KB. 

▪ Test Edit mode allows you to easily test modifications to a running program. 

▪ Bit-in-word referencing. 

▪ Battery-backed calendar clock. 

▪ In-system upgradeable firmware. 

▪ Three isolated serial ports: an RS-485 serial port, an RS-232 serial port, and an RS-232  Ethernet station manager serial port. 

▪ The embedded Ethernet interface provides: 

- Data exchange using Ethernet Global Data (EGD) 

- TCP/IP communication services using SRTP 

- Support for SRTP Channels, Modbus/TCP Server, and Modbus/TCP Client 

- Full programming and configuration services 

- Comprehensive station management and diagnostic tools 

- Two full-duplex 10BaseT/100BaseT/TX (RJ-45 Connector) ports with an internal network  switch providing auto-negotiated network speed, duplex mode, and crossover detection. 

- User-configurable Redundant IP address 

- Time synchronization to SNTP time server on Ethernet network (when used with  Release 5.00 or later CPU module).

Features 

▪ Contains 10 Mbytes of battery-backed user memory and 10 Mbytes of non-volatile flash user  memory. 

▪ Provides access to bulk memory via reference table %W. 

▪ Configurable data and program memory. 

▪ Programming in Ladder Diagram, C, Structured Text, and Function Block Diagram. 

▪ Supports auto-located Symbolic Variables that can use any amount of user memory. 

▪ Reference table sizes include 32Kbits for discrete %I and %Q and up to 32K words each for  analog %AI and %AQ. 

▪ Supports Series 90-70 discrete and analog I/O, communications, and other modules. For a  list of modules supported, refer to the PACSystems RX7i Installation Manual, GFK-2223. 

▪ Supports all VME modules supported by Series 90-70. 

▪ Supports RX7i data monitoring over the web. Allows a combined total of up to 16 web server  and FTP connections. 

▪ Supports up to 512 program blocks. Maximum size for a block is 128KB. 

▪ Test Edit mode allows you to easily test modifications to a running program. 

▪ Bit-in-word referencing. 

▪ Battery-backed calendar clock. 

▪ In-system upgradeable firmware. 

▪ Three isolated serial ports: an RS-485 serial port, an RS-232 serial port, and an RS-232  Ethernet station manager serial port. 

▪ The embedded Ethernet interface provides: 

- Data exchange using Ethernet Global Data (EGD) 

- TCP/IP communication services using SRTP 

- Support for SRTP Channels, Modbus/TCP Server, and Modbus/TCP Client 

- Full programming and configuration services 

- Comprehensive station management and diagnostic tools 

- Two full-duplex 10BaseT/100BaseT/TX (RJ-45 Connector) ports with an internal network  switch providing auto-negotiated network speed, duplex mode, and crossover detection. 

- User-configurable Redundant IP address 

- Time synchronization to SNTP time server on Ethernet network (when used with  Release 5.00 or later CPU module).