IS200TREGH1A | General Electric Gas Turbine Emergency Trip Board

IS200TREGH1A | General Electric Gas Turbine Emergency Trip Board

Product Description P/N: IS200TREGH1A DESCRIPTION / SPECIFICATIONS Description The IS200TREGH1A is a Gas Turbine Emergency Trip Board. This board is designed to be used in gas turbine control systems. It is a critical safety component responsible for executing emergency shutdown procedures in the event of a detected fault or unsafe condition. 

The board interfaces with various sensors and control systems to monitor turbine parameters and initiate a trip command if necessary. Technical Specifications Condition New / Never Used Surplus Part Number IS200TREGH1A Manufacturer General Electric Series Mark VI Product Type Emergency Trip Terminal Board Number of Trip Solenoids 3 Relay Outputs 3 Trip Inputs 125/24 V dc Solenoid Response Time 0.1 sec Size 17.8 cm wide x 33.02 cm Information About IS200TREGH1A The IS200TREGH1A is a Gas Turbine Emergency Trip Board from the Mark VI series designed by General Electric. This model is intended to work in conjunction with the VPRO Turbine Emergency Trip Module. 

When integrated with the VPRO I/O Processor Board, it also interfaces with two additional terminal boards: the TPRO (Turbine Protection) and TRPG (Primary Trip) boards. The IS200TREGH1A serves as the positive side to the available 125 VDC solenoids, while the TRPG model functions as the negative side. The IS200TREGH1A model controls the twelve relays on the VPRO board. Nine of these relays form three groups of three, which are used to form vote inputs to control the three trip solenoids on the VPRO processor. Additionally, a second IS200TREGH1A board can be connected to the VPRO processor, driven from the VPRO board to the J4 connector. 

 Manufacturer information General Electric (GE) is a multinational conglomerate founded in 1892, based in the United States. It operates in various industries, including aviation, healthcare, renewable energy, and power. GE is known for its innovations in technology, manufacturing, and infrastructure solutions. IQElectro is not an authorized distributor. QElectro LLC (IQElectro) is NOT an Authorized Distributor or in any way affiliated with Rockwell Automation, Siemens, or any other Manufacturers. IQElectro is NOT an Authorized Dealer of this product. The product may be of older version, date codes, or design than that available from authorized dealers. As IQElectro is not an authorized dealer of this product, the Original Manufacturer's Warranty and Support DO NOT apply.IQElectro sells SURPLUS onlyand DOES NOT SELL SOFTWARE or FIRMWARE licenses For more detailed information, please refer to the full version of our disclaimer policy Disclaimer Policy.

Compatibility 

ƒ Compatible with any Series 90-30 CPU except IC693CPU321 and IC693CPU340. Configuration size is limited for CPU311/313/331, as described on the next page. 

ƒ Requires release 8.0 CPU firmware. The latest Release 10 is recommended, if available for the particular CPU. 

ƒ Requires CIMPLICITY Machine Edition Logic Developer PLC version 3.0 plus the appropriate service pack or special (or a version later than 3.0). 

ƒ Not compatible with the VersaPro™, Control, or Logicmaster™ programming software. 

ƒ The Series 90-30 Hand-Held Programmer (IC693PRG300) cannot be used to configure this module. New Features The Series 90-30 DeviceNet Master Module allows a Series 90-30 PLC to send and receive I/O data from a DeviceNet network. 

Module features include: 

ƒ Support for all standard data rates (125K, 250K, 500K) 

ƒ Support for 255 bytes input data transfer and 255 bytes output data transfer per slave 

ƒ Support for 3972 bytes of input data transfer and 3972 bytes of output data transfer per master 

ƒ Support for two I/O connections per Slave - Typically one connection is used for Polled and the other is used for Strobe, Cyclic, or COS 

ƒ Support for Poll, Strobe, Cyclic and COS I/O Connections, Fragmented I/O and Explicit Messaging 

ƒ Support for Unconnected Message Manager (UCMM) with 1 proxy connection per slave device 

ƒ Support for configuration of the global scan rate 

ƒ Support for configuration of update rates for Poll and COS/Cyclic on a connection basis 

ƒ Support for PLC-application initiated explicit messaging via a COMMREQ 

ƒ Master can be configured to operate as a slave simultaneously with master operation 

ƒ Configurable fault behavior on loss of communication 

ƒ Reports loss or reestablishment of communication with slaves in PLC fault table (configurable) 

ƒ Support for 64 network device status bits (note: the bit for the master itself is always zero) 

ƒ Firmware update via service port on module