GE IS200SCLTH1A LM CA TMR TB

GE IS200SCLTH1A LM CA TMR TB

Part Number IS200SCLTH1A Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VI Function Module Availability In StockIS200SCLTH1A is a GE Mark VI series Power Distribution Module. The MK VI gas turbine control system from General Electric is an advanced digital turbine control system. The I/O interface is intended for direct communication with the turbine's sensors and actuators. The sophisticated interface does away with the requirement for interposing instrumentation, as well as the reliability and maintenance difficulties that come with it. 

The current state-of-the-art control for GE Turbines is the GE General Electric Mark VI Speedtronic Turbine Control System. It's a fully integrated control system with protection and monitoring for gas and steam turbine generators and mechanical drive applications. The Mark VI turbine control is a fully integrated control, protection, and monitoring system for gas and steam turbine generator and mechanical drive applications. It's also a great place to put all of your power island and balance-of-plant controls.

The IO module has the following main functions

Input Function

The IO module can receive input signals sent by external devices and convert them into digital or analogue signals for use by the computer system or control system. These input signals can come from a variety of sensors, such as temperature sensors, pressure sensors, photosensitive sensors and so on. By receiving and parsing these input signals, the system can monitor and control the external environment in real time.

Output Functions

The IO module is capable of converting the output signals generated by a computer system or control system into the form required by an external device. These output signals are typically used to control actuators such as motors, valves, lights, etc. By sending appropriate output signals to external devices, the system enables control and operation of the external environment.

Data Acquisition and Processing

The IO module is capable of acquiring data from external devices and transferring it to a computer system or control system for further processing. This enables the system to acquire environmental data, status information and user inputs in real time and make appropriate decisions or perform specific tasks based on these data.

Communication Interfaces

IO modules are usually equipped with different types of communication interfaces, such as serial interfaces (RS232, RS485), Ethernet interfaces, CAN bus interfaces, and so on. These interfaces enable IO modules to exchange data and communicate efficiently with computer systems or other external devices.

OTHER INFORMATION

• Up to 1.26 GHz Pentium® III processor with 256 KB advanced  transfer cache  

• Up to 512 MB PC-133 SDRAM using a single SODIMM  

• Internal AGP SVGA controller with 4 MB display cache  

• 133 MHz system bus via Intel® 815E chipset  

• Dual Ethernet controllers supporting 10BaseT and 100BaseTX  interfaces  

• Optional PCI dual channel Ultra160 SCSI  

• Up to three (two with rear I/O support) PMC expansion sites  (IEEE-P1386 common mezzanine card standard, 5 V)  

• Up to 1 GB bootable flash on secondary IDE (optional)  

• Two 16-bit and two 32-bit programmable timers  

• 32 KB of nonvolatile SRAM  

• Software-selectable watchdog timer with reset  

Instructions and warnings related to the operation of the product:

The following specifications must be strictly observed:

 The technical specifications and typical applications of the product system must be strictly observed.

 PERSONNEL TRAINING: Only trained personnel may install, operate, maintain or repair the product system. These personnel must be instructed on the

These personnel must be instructed and briefed on the conditions in the hazardous area.

 Unauthorised modifications: No modifications or structural changes may be made to the product system.

 Maintenance Responsibility: It must be ensured that the product system is used only under appropriate conditions and in a condition fully suitable for use.

 Working environment: The user must fulfil the specified environmental conditions:

Safety regulations

The following safety regulations must be fully observed when (maintenance) work is carried out on the product system:

1 Disconnect completely.

2 Secure to prevent reconnection.

3 Confirm that the installation has been completed.

4 Perform grounding and short-circuiting.