GE IS200TBAIS1C - TERM. BOARD ANALOG INPU

GE IS200TBAIS1C - TERM. BOARD ANALOG INPU

Part Number IS200TBAIS1C Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VIe Function Module Availability In StockIS200TBAIS1C is a safety-certified Analog Input/Output terminal board. TBAI consists of 3 DC-37 pin connections for connecting to the I/O processors. A single connector is used to accommodate simplex applications (JR1). All three connectors are compatible with TMR applications. 

The input signals for the R, S, and T controls are fanned to the three connections in TMR applications. TMR outputs aggregate the currents of the three connected output drivers and use a measuring shunt to calculate the overall current. The total current signal is then presented to the I/O processors for regulation to the requested setpoint. TBAIS1C is a safety-certified product. In the Mark VIeS SIS, YAIC does not support the 200 mA output option. 

TMR applications can use the same terminal board. IS200TBAIS1C Installation The following analog I/O types can be accommodated by TBAI: Analog input, two-wire transmitter; Analog input, three-wire transmitter; Analog input, four-wire transmitter; 5 V, 10 V dc analog input 0-20 mA analog output 0-200 mA analog output IS200TBAIS1C Operation Each 24 V dc power output is rated for continuous output of 21 mA and is safeguarded against short circuit operation. The control system's 24 V dc supply can power the transmitters/transducers, or they can be powered separately. The JO jumper determines the current output type. Each output is monitored by diagnostics, and if a fault cannot be cleared by a command from the processor, a suicide relay in the I/O controller disconnects the relevant output. Physical Characteristics Fault detection Monitor total output current. 

Check for hardware incompatibility using the connection ID chip. Temperature range -30C to 65C Dimensions 10.16 cm wide by 33.02 cm tall Diagnostics The I/O controller interrogates each cable connector on the terminal board for its individual ID device. The ID device is a read-only chip coded with the terminal board serial number, board type, revision number, and the JR, JS, JT connection location. A hardware incompatibility fault is issued when the I/O controller reads this chip and finds a mismatch. Configuration The following are the options for jumpers: Jumpers J1A through J8A allow you to choose between current and voltage input. Jumpers J1B to J8B determine whether the return is linked to common or not. Choose between 1 mA and 20 mA input current using jumpers J9A and J10A.Module manufactured by General Electric as part of the Mark VI/VIe Series used in gas turbine sppedtronic control systems

OTHER INFORMATION

• Celeron™ socket 370-based single-board computer (SBC) with operating  system support for Windows NT®/Windows® 2000, Linux, VxWorks, QNX,  and Solaris 

• Special features for embedded applications 

— Up to 512 Mbyte IDE CompactFlash (optional) 

— Three programmable 16-bit timers 

— 32 Kbyte of battery-backed SRAM 

— Remote Ethernet booting supported 

— Software-selectable watchdog timer with reset 

— Supports VMEbus P2 connection to HD/floppy drive 

— PMC expansion site with VMEbus P2 I/O 

— PC•MIP expansion site supported 

— VME64 modes supported: A32/A24/D32/D16/D08(EO)/MBLT64/BLT32 

— VMEbus interrupt handler, interrupter, and system controller 

— Includes byte-swapping hardware for little-endian and big-endian data  interfacing (patent no. 6,032,212) 

— Enhanced bus error handling 

— Passive heat sink design (no moving parts) 

• Standard features include 

— Celeron socket 370 processor 

— Up to 256 Mbyte SDRAM using one 144-pin SODIMM 

— 64-bit Intel® AGP SVGA controller with 2 Mbyte SGRAM 

— On-board Fast Ethernet controller supporting 10BaseT and 100BaseTX  interfaces 

— On-board Ultra DMA/33 hard drive and floppy drive controllers with  VMEbus P2 I/O 

— Two high-performance 16550-compatible serial ports 

— PS/2-style keyboard and mouse port on front panel 

— Real-time clock and miniature speaker included