EATON SPD series surge protector

Here are some typical VPR data examples:

50kA direct busbar installation unit VPR

Voltage code protection mode L-N L-G N-G

230L 1000 2000 1000

240S 500 1000 500

208Y/220Y 500 1000 500

400Y/480Y 1000 2000 1000

600Y 1200 2500 1200

240H 500 1000 500

50kA connected unit VPR through circuit breaker

Voltage code protection mode L-N L-G N-G

230L 1200 2000 1200

240S 700 1200 700

208Y/220Y 700 1200 700

400Y/480Y 1200 2000 1200

600Y 1500 2500 1500

240H 700 1200 700

The VPR data for higher surge capacity levels are detailed in Tables 4 to 11 of the original text.

Technical specifications

Electrical parameters

Parameter specifications

Nominal discharge current (In) 20kA

Short circuit current rating (SCCR) 200kA

Power frequency 50/60 Hz (Power Xpert SPD only tests 60 Hz)

Power consumption (basic type) 0.5W~1.3W (depending on voltage code)

Power consumption (standard/with counter) 0.6W~2.1W (depending on voltage code)

Power consumption (Power Xpert SPD) 4W (all voltage codes)

Maximum Continuous Operating Voltage (MCV)

Voltage code L-N L-G N-G L-L

208Y/220Y/240S 150 300 150 300

230L 320 640 320 —

400Y/480Y 320 640 320 640

600Y 420 420 420 840

240D — 300 — 300

480D — 640 — 640

600D — 840 — 840

protected mode

Single phase: L-N, L-G, N-G, L-L

Three phase star: L-N, L-G, N-G, L-L

Three phase triangle: L-N, L-G, L-L

relay output

Contact type: Form C (one normally open and one normally closed)

Rated value: 150 Vac @ 0.46A, 30 Vdc @ 1A

Logic:

Normal power on state: NO contact open, NC contact closed

Power failure status: NO contact closed, NC contact disconnected

environmental parameters

Working temperature: -40 ° C to+50 ° C (-40 ° F to+122 ° F)

Working humidity: 5%~95% (without condensation)

Working altitude:

Standard SPD: up to 5000 meters

Power Xpert SPD: up to 2000 meters

Seismic resistance: meets the requirements of IBC 2018, CBC 2007, and UBC Zone 4

mechanical parameters

Surge capacity weight

50-200kA approximately 1.6 kg (3.5 lb)

250-400kA, approximately 3.2 kg (7.0 lb)

wiring

Factory pre connected 18 inch # 10 AWG wire (for installing suffixes B, C, J)

Certification and Standards

The SPD series has passed multiple international authoritative certifications:

Standard description

UL 1449 5th Edition Surge Protection Device Standard

UL 1283 7th Edition Electromagnetic Interference Filter Standard

CSA C22.2 No. 269.2-17 Surge Protection Device - Type 2

CSA C22.2 No. 269.4-17 Surge Protection Devices - Type 4 Components

UL 60950-1 Information Technology Equipment Safety

UL 2900-1 Networking Product Software Network Security (Power Xpert SPD)

ICES/FCC Part 15 Subpart B Class A Conducted and Radiated Emission Limits

IEC 255-21-1/2 Seismic Testing of Relays

IEEE 693-2018 Seismic Design of Substations

In addition, the SPD series can be used to meet:

UL 96A Lightning Protection System Standard

NFPA 780 Installation Standard for Lightning Protection Systems

RoHS Hazardous Substance Restriction Directive

Selection and ordering information

Catalog Number Configuration Rules

Location Options Description

Series SPD surge protection device

KA level 05008010012016020025030400 Surge capacity per phase

Voltage codes 230L, 240S, 208Y, 220Y, 400Y, 480Y, 600Y, 240D, 480D, 600D, 240H System voltage and configuration

Function Package 1=Basic Type, 2=Standard Type, 3=Standard Type+Counter, 4=Power Xpert SPD Function Level

Application A=direct busbar installation of distribution panel, B=switchgear, C=distribution panel/switch board/busbar, J=installation method of motor control center

Selection example

SPD250480D2J meaning:

SPD series

250kA per phase

480V Triangle System (480D)

Standard Feature Pack (2)

Application of Motor Control Center (J)

Precautions

PRL1a, 2a, 3a, 3e distribution panel direct busbar installation only supports 50-200kA, using the suffix "A"

When the same distribution panel is connected through a circuit breaker, use the suffix "C"

Power Xpert SPD is not suitable for corner grounded delta systems and requires voltage on each phase to function properly

240V high foot triangle (4W+G) B-phase high foot is standard configuration. If you need C-phase high foot, please consult the factory