ABB mechanical frequency converter ACS180 inverter

User interface Overview:

• In Home view, press the Back key to open the Options view.

• In the home view, press the OK key to open the menu.

• Use the arrow keys to navigate through the view.

• Press OK to open the highlighted Settings or items.

• Use the left and right arrow keys to highlight a value.

• Use the up and down arrow keys to set values.

• Press the Back key to cancel Settings or return to the previous view.

■ Home view

The home page view shows the reading of one of the three measurement signals. Use the left and right arrow keys to select the page.

The status bar at the top of the home view shows:

Control position (Loc for local control, Rem for remote control)

• Status icon

• Give the target value

From the home view, press the Back key to open the options view, and press the OK key to open the menu.

Use the up and down arrow keys to adjust the current given value.

■ Message view

For fault and warning information, see the ACS180 Firmware manual (3AXD50000467860[English]). To reset the fault, press the OK key (reset with soft key label).

■ Options view

To open the options view, press the back key in the home view.

In the Options view, you can:

• Set the control position

• Set the direction of the motor

• Set the given value

• Check the active fault

• View the list of active warnings

■ Menu

To open the menu, press the OK key in the home view.

To navigate through the menu, press the up and down arrow keys to move between menu items.

Menu item:

• Motor data view: Enter motor specifications.

• Motor Control view: Set motor control Settings.

• Control Macro view: Select the connection parameter macro.

• Diagnostic view: Read active faults and warnings.

• Parameter view: Open and edit the full parameter list.

Installation mode

You can install the inverter to the assembly plate with screws.

Installation requirements:

• Ensure that there is at least 75mm free space at the top and bottom of the inverter (in the cooling air inlet and outlet).

• Multiple inverters can be installed side by side.

• The maximum ambient temperature is 40°C if inverters of dimension R0 are installed side by side.

• Frequency converters with dimension R0 should be installed upright. The frequency converter with size R0 has no cooling fan.

• When installing a frequency converter with dimension R1, it is possible to tilt up to 90 degrees from the vertical direction to the full horizontal direction.

• Ensure that the heated cooling air discharged from the inverter does not enter the cooling air intake of other equipment.

• Install the inverter in the cabinet or housing. The cabinet-mounted inverter has IP20 protection rating.

Check the installation site

Check the installation site. Ensure:

• Adequate ventilation or cooling at the installation site to remove heat from the inverter. See Technical Data.

• The environmental conditions of the drive meet the relevant specifications. See technical data.

• The material above and below the walls and equipment behind the inverter is non-flammable.

• The mounting surface should be as close to vertical as possible and strong enough to support the inverter.

• Adequate space around the inverter for cooling, maintenance and operation.

• Ensure that there are no strong magnetic field sources near the inverter, such as high-current single-core wires or contactor coils. Strong magnetic fields can cause interference or lead to inaccuracies in the operation of the inverter.

Tools needed

To install the inverter mechanically, you need to use the following tools:

• Hand drill and suitable drill bit

• Bring a screwdriver or wrench with a suitable tool head

• Measuring tape and level

• Personal protective equipment.

Open the box and inspect the deliverables

The following is the frequency converter and its contents. Make sure all items are present and there are no signs of damage.

Package contents:

• Frequency converter

• Mounting accessories (wire clamps, metal flooring, screws, etc.)

• Quick installation and startup guide.

Check motor and inverter compatibility

The asynchronous AC induction motor or permanent magnet synchronous motor is used with the frequency converter. When the scalar motor control mode is used, multiple induction motors can be connected to the inverter simultaneously.

Ensure motor and inverter compatibility according to the rating table in the technical data.

Select power cable

■ General Guidelines

Select power and motor cables according to local regulations:

• Current: Select the cable that can carry the maximum load current and is suitable for the expected short circuit conditions provided by the power supply network. The installation method and ambient temperature affect the current carrying capacity of the cable. Comply with local regulations and laws.

• Temperature: For IEC equipment, the cable can withstand a temperature of at least 70 °C (158 °F) during long-term operation. For North America, choose cables with a temperature rating of at least 75 °C (167 °F).

• Voltage: 600 V AC cables can accept voltages up to 500 V AC. A 750 V AC cable can accept voltages up to 600 V AC. A 1000 V AC cable can accept voltages up to 690 V AC.

Choose Xiamen control Smith after sale worry