GE DS215DMCAG2AZZ02A Drive Board Module

GE DS215DMCAG2AZZ02A Drive Board Module

Part Number DS215DMCAG2AZZ02A Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VI/VIe Function Module Availability In StockDS215DMCAG2AZZ02A is a Drive Board Module under Mark V series. The DS215DMCAG2AZZ02A is a circuit board component developed by General Electric for use in their Mark V gas/steam turbine control system. The MKV was a member of GE's Speedtronic range, which debuted in the late 1960s and evolved throughout the century. While Mark V circuit boards are no longer available as OEM parts, they can be ordered as fully inspected and refurbished units from World of Controls. 

 This board, like other DS215 boards, has more firmware or hardware than a similar-named DS200 board. The DS215DMCAG2AZZ02A is simple to install due to factory-made drill holes in each board corner. Additional drill holes can be found along the board's edges and within the board's body. For easy alignment, the unit's borders are marked with lettering and/or numbering, and it contains multiple codes for identification. A vertically placed auxiliary board populates the board. 

The auxiliary board is located in the bottom left corner of the board, close to a second optional auxiliary board that mounts parallel to the board's surface. A single female vertical connection, four male vertical pin cable connectors, and three header connectors are among the board's connectors. Two heat sinks, an inductor coil, fourteen jumper switches, fuse components, a push-button reset switch, LED indicators, and transistors are all found on the board. It has about fifty integrated circuits, twenty resistor network arrays, and a variety of diodes, resistors, and capacitors constructed of polyester vinyl, ceramic, aluminum, and tantalum electrolytic materials.

Features 

▪ Contains 10 Mbytes of battery-backed user memory and 10 Mbytes of non-volatile flash user  memory. 

▪ Provides access to bulk memory via reference table %W. 

▪ Configurable data and program memory. 

▪ Programming in Ladder Diagram, C, Structured Text, and Function Block Diagram. 

▪ Supports auto-located Symbolic Variables that can use any amount of user memory. 

▪ Reference table sizes include 32Kbits for discrete %I and %Q and up to 32K words each for  analog %AI and %AQ. 

▪ Supports Series 90-70 discrete and analog I/O, communications, and other modules. For a  list of modules supported, refer to the PACSystems RX7i Installation Manual, GFK-2223. 

▪ Supports all VME modules supported by Series 90-70. 

▪ Supports RX7i data monitoring over the web. Allows a combined total of up to 16 web server  and FTP connections. 

▪ Supports up to 512 program blocks. Maximum size for a block is 128KB. 

▪ Test Edit mode allows you to easily test modifications to a running program. 

▪ Bit-in-word referencing. 

▪ Battery-backed calendar clock. 

▪ In-system upgradeable firmware. 

▪ Three isolated serial ports: an RS-485 serial port, an RS-232 serial port, and an RS-232  Ethernet station manager serial port. 

▪ The embedded Ethernet interface provides: 

- Data exchange using Ethernet Global Data (EGD) 

- TCP/IP communication services using SRTP 

- Support for SRTP Channels, Modbus/TCP Server, and Modbus/TCP Client 

- Full programming and configuration services 

- Comprehensive station management and diagnostic tools 

- Two full-duplex 10BaseT/100BaseT/TX (RJ-45 Connector) ports with an internal network  switch providing auto-negotiated network speed, duplex mode, and crossover detection. 

- User-configurable Redundant IP address 

- Time synchronization to SNTP time server on Ethernet network (when used with  Release 5.00 or later CPU module).