Welcome to the Industrial Automation website!

NameDescriptionContent
XING-Automation
E-mail  
Password  
  
Forgot password?
  Register
当前位置:

AB 1771-IFE A/B/C Analog Input Module

F: | Au:FAN | DA:2025-04-21 | 1000 Br: | 🔊 点击朗读正文 ❚❚ ▶ | Share:

AB 1771-IFE A/B/C Analog Input Module

Preparation before installation:

Static electricity protection: the module is sensitive to static electricity, touch grounded objects, 

wear a wrist strap when operating, avoid touching the backplane connectors and internal circuit components, 

and place it in a static shielding box when not in use.


Directive Compliance: CE marked, compliant with EU EMC and Low Voltage Directives, meets relevant standards.

Compatibility: Can be used in 1771 I/O chassis, but not with 1771-AL PLC - 2/20 or 2/30 local adapters.

Power Calculation: Module draws 500mA from the 1771 I/O power supply and needs to calculate the total power in the chassis to prevent overloading.

Module Positioning: Can be installed in slots other than the leftmost slot (reserved for PC processor or adapter modules) 

with care to avoid electromagnetic interference.


Installation Procedure:

Jumper Setting: If replacing an A or B series module, set the A/B analogue jumper from POS G to POS E; select the input type (voltage or current) 

by configuring the jumper, but all inputs must be either single-ended or differential and cannot be mixed .

Module Installation: Smoothly insert the module into the chassis rails after power is removed, secure the chassis latch and locking lever, 

and connect the 1771-WG wiring arm.

Wiring Connection: Connect the I/O devices, note the difference in connection between single-ended and differential inputs, 

avoid mixing 2-wire and 4-wire transmitter inputs, the sensor cable should be shielded and grounded.

Grounding operation: The foil shield and drain wire of the shielded cable are grounded at one end only, 

connected to the chassis mounting bolts, and insulated at the other end.

Module Configuration: A wide range of parameters can be configured via the Block Transfer Write command, 

such as 7 input voltage or current ranges, data format (BCD or binary), real-time sampling (100 ms - 3.1 sec selectable), 

digital filtering (0.00 BCD - 0.99 BCD),** scaling (max range ±9999 BCD)**, etc. 

The default configuration is 1 - 5V dvd. Default configurations are 1 - 5V dc or 4 - 20mA, BCD format, no real-time sampling, etc.

Troubleshooting: There are green RUN and red FAULT indicators on the front panel of the module, 

and faults can be judged by the status of the indicators and the status bits in the BTR file. 

If RUN blinks and FAULT is off, it means waiting for configuration; if RUN is off and FAULT is on, it may be a hardware failure.


Module specification:

| Description | Values

|---|---| Inputs per module | 16

| Inputs per module | 16 single-ended; 8 differential low | Module Position | 1771


| Input Voltage Range |+1 to +5V dc, 0 to +5V dc, etc. | Input Current Range |+1 to +5V dc, 0 to +5V dc, etc.

| Input Current Range +1 to +5V dc, 0 to +5V dc, etc. | Input Voltage Range +1 to +5V dc, 0 to +5V dc, etc.

Input Current Range |+4 to +20mA, 0 to +20mA, etc. | Resolution | 12-bit binary (12-bit plus sign bit for bipolar range)

Accuracy | 0.1% of full scale range @ 25°C| | Linearity | ±1% of full scale range @ 25°C

| Linearity |±1 LSB| | Repeatability |±1 LSB| | Repetition

| Repeatability |±1 LSB| | Isolation Voltage

| Isolation Voltage | Meets or exceeds UL Standard 508 and CSA Standard C22.2 No. 142.

| Input Overvoltage Protection | Voltage Mode 200V, Current Mode 8V| | Input Overcurrent Protection | Voltage Mode 200V, Current Mode 8V

Input Overcurrent Protection |30mA| Common Mode Voltage |±0.5V, Current Mode 8V

Input Overcurrent Protection |30mA| Common Mode Voltage |±14.25V

| Input Impedance | Voltage range >10 megohms; Current range 250 ohms | Common Mode Rejection Ratio

| Common Mode Rejection Ratio | 80 db, dc - 120Hz | Common Mode Voltage | ±14.25V | Input Impedance

Current Requirement | 500mA @ +5V (I/O chassis backplane)| | Power Consumption | 2.5mA @ +5V (I/O chassis backplane)

Power Consumption | 2.5 Watts (Max) | Thermal Dissipation | 8.5 Watts (Max)

| Thermal Dissipation | 8.52 BTU/hr (max)| | Power Consumption | 2.5 Watts (max)

| Unscaled Output | Polarity Range 0000 to +4095; Bipolar Range - 4095 to +4095|

| Engineering Units Output | ±9999 (optional scaling)| | Internal Scan Rate | 8

| Internal Scan Rate | 8-way differential unfiltered 13.7ms; 16-way single-ended unfiltered 27.4ms | Environmental Conditions | Operating Temperature

| Environmental Conditions | Operating Temperature 0 - 60 °C 0 - 60 ∘Operating Temperature 0 - 60Operating Temperature 0 - 60 ∘ C

Operating Temperature 0 - 60 ∘ C; Storage Temperature - 40 - 85∘C

Relative humidity 5 - 95% (non-condensing) | Conductor gauge | 14 gauge (non-condensing)

| Conductor Gauge | 14 gauge (2mm 2mm Stranded Wire (Max)3/64inch (1.2mm) insulation (maximum); Category 2

| Keyed Positions | Between 10 - 12, 24 - 26

| Keyed Positions | Between 10 - 12, 24 - 26 | Wiring Arms

| Junction Arm | Catalog Number 1771-WG

| Junction Arm Screw Torque | 7 - 9 in-lb | Keyed Positions | 10 - 12, 24 - 26

| Agency Approvals | Class 1 Div 2 Hazardous; CE marking (applies to directives)| | Series Differences: A, B, and C


Series Differences: The A, B, and C series modules differ in indicator lights, input data handling, default scaling, block transfer length, 

  • Rexroth HCS02.1E-W0028-A-03 CSH01.1C-PB Drive Package
  • Bosch Rexroth VT-VARAP 1-537-20/V0 Amplifier
  • Bosch Rexroth PPC-R02.2N R911285402 Control Unit
  • National Instruments PCI-7342 Motion Controller
  • National Instruments PXIe-6535 Digital I/O Module
  • National Instruments PCIe-6738 Analog Output Card
  • National Instruments NI-6583 Digital I/O Adapter Module
  • National Instruments NI TB-9214 Terminal Block
  • National Instruments NI 9222 Simultaneous Analog Input Module
  • National Instruments PXIe-8364 MXI-Express Module
  • National Instruments PXI-8185 Embedded Controller
  • National Instruments PCI-1405 Device
  • National Instruments SCXI-1160 Module
  • National Instruments PCI-MIO-16E-1 Device
  • National Instruments USB-6216 Device
  • National Instruments PXIe-2543 Module
  • National Instruments PCI-5102 Digitizer
  • National Instruments PXI-6284 DAQ Device
  • National Instruments PXI-7330 Controller
  • National Instruments cFP-2100 Controller
  • National Instruments USB-6002 DAQ Device
  • National Instruments PCIe-6374 Multifunction DAQ Card
  • National Instruments PXIe-4610 Power Amplifier Module
  • National Instruments PXIe-4154 Battery Simulator
  • National Instruments PXIe-7858R Reconfigurable I/O Module
  • National Instruments BNC-2090A BNC Terminal Block
  • National Instruments cRIO-9066 CompactRIO Controller
  • National Instruments 198944C-04L Ordering Part Number
  • National Instruments 157732A-02L Ordering Part Number
  • National Instruments TC-4353 Thermocouple Terminal Block
  • National Instruments 190996F-04L PCI-6250 DAQ Part Number
  • National Instruments PCI-7334 Controller
  • National Instruments TRC-8542 Cable
  • National Instruments CAP-1804 Accessory
  • National Instruments myRIO-1900 Kit
  • National Instruments PCI-AI16HR Board
  • National Instruments PCIe-6341 Device
  • National Instruments PXI-6514 Module
  • National Instruments PXI-6025E DAQ Card
  • National Instruments DAQPad-6015 Device
  • National Instruments BNC-2090 Accessory
  • National Instruments USB-4431 Dynamic Signal Module
  • National Instruments 181045-02 Ordering Part Number
  • National Instruments 779697-02 Ordering Part Number
  • National Instruments cFP-AI-112 Analog Input Module
  • National Instruments PCI-6602 Counter Timer Card
  • National Instruments NI-9871 RS485 Interface Module
  • National Instruments NI 9238 Voltage Input Module
  • National Instruments USB-6001 USB-6008 DAQ Devices
  • National Instruments PXI-6289 Multifunction DAQ Card
  • National Instruments PCI-7340 Motion Controller
  • National Instruments PCI-6036E DAQ Device
  • National Instruments USB-6002 DAQ Device
  • National Instruments NI-9201 Module
  • National Instruments SCXI-1531 Module
  • National Instruments 779351-01 Module
  • National Instruments PCI-6071E DAQ Device
  • National Instruments PCI-8512 Device
  • National Instruments NI 9375 I O Module
  • National Instruments PCI-8431/2 Card
  • National Instruments PXI-4472 Module
  • National Instruments PXI-6527 Digital Module
  • National Instruments PXI-7344 Motion Controller
  • National Instruments 779553-50 Ordering Part Number
  • National Instruments PXI-6040E Multifunction DAQ Module
  • National Instruments PCI-6013 Multifunction DAQ Card
  • National Instruments SCB-68 Shielded Connector Block
  • National Instruments PXI-7350 Motion Controller
  • National Instruments PXI-5142 Digitizer Oscilloscope Card
  • National Instruments 781157-01 Ordering Part Number
  • National Instruments cRIO-9057 CompactRIO Controller
  • National Instruments NI 9881 Module
  • National Instruments USB-8506/2 Device
  • National Instruments PCIe-8255R Device
  • National Instruments NI 9218 Module
  • National Instruments TB-2709 Terminal Block
  • National Instruments PXIe-1075 Chassis
  • National Instruments PCI-6254 DAQ Device
  • National Instruments FP-1000 Network Module
  • National Instruments 780876-01 Output Module
  • National Instruments PXI-6225 DAQ Module
  • National Instruments FW-7344 Motion Controller
  • National Instruments PCI-488.2 GPIB Interface Card
  • National Instruments PXIe-4300 Analog Input Module
  • National Instruments PXIe-8360 MXI-Express Interface
  • National Instruments SCXI-1120 Isolated Amplifier Module
  • National Instruments PCIe-6341 DAQ Device
  • National Instruments PXI-6723 Module
  • National Instruments PXI-5404 Source
  • National Instruments SH200LF Switch Cable
  • National Instruments PCI-6023E DAQ Card
  • National Instruments TB-4302C Terminal Block
  • National Instruments PXI-8430/2 Module
  • National Instruments 779892-02 Module
  • National Instruments QNET-04838 Actuator Board
  • National Instruments NI 9871 RS485 Interface Module
  • National Instruments PCI-6250 Multifunction DAQ Card
  • National Instruments cDAQ-9188 Ethernet Chassis
  • National Instruments PXI-5441 Arbitrary Waveform Generator
  • National Instruments MID-7604 Motion Interface Device
  • National Instruments FP-DO-403 Digital Output Module
  • National Instruments cRIO-9114 Reconfigurable Chassis
  • National Instruments SCXI-1126 Frequency Input Module
  • National Instruments 776572-60 Ordering Part Number
  • National Instruments PCI-7332 Motion Control Card
  • National Instruments NI-9217 RTD Input Module
  • National Instruments PCI-6023E Multifunction DAQ Card
  • National Instruments PXI-6650H Timing Module
  • National Instruments PXI-8196 Embedded Controller
  • National Instruments PXI-6528 Isolated Digital I/O Board
  • National Instruments PXI-6120 Simultaneous DAQ Card
  • ALSTOM 029.204 687 Digital I/O VME Board
  • National Instruments PXI-6509 Digital I/O Module
  • National Instruments FP-AI-112 Analog Input Module
  • National Instruments cRIO-9065 CompactRIO Controller
  • National Instruments PXI-2570 SPDT Relay Module
  • National Instruments PXI-5610 Module
  • National Instruments cFP-RTD-122 Module
  • National Instruments PXI-8336 Module
  • National Instruments NI 9237 Module
  • National Instruments PCI-6224 DAQ Card
  • National Instruments USB-6218 DAQ Device
  • National Instruments PCI-6601 Device
  • National Instruments SCXI-1124 Module
  • National Instruments USB-6525 DIO Device
  • National Instruments cDAQ-9189 Chassis
  • National Instruments PXIe-8394 MXI Module
  • National Instruments PXIe-4112 Power Supply