Welcome to the Industrial Automation website!

NameDescriptionContent
XING-Automation
E-mail  
Password  
  
Forgot password?
  Register
当前位置:

ABB IMASI23 module

F: | Au:FAN | DA:2025-05-15 | 1781 Br: | 🔊 点击朗读正文 ❚❚ ▶ | Share:

ABB IMASI23 module

product overview

The ABB IMASI23 module is an analog input module designed specifically for industrial automation systems, responsible for critical data acquisition tasks in industrial control systems. It can convert analog signals from various sensors on site, such as temperature, pressure, flow rate, liquid level, and other physical quantities, into digital signals and transmit them to the control system, providing accurate data basis for precise control and decision-making of the system. It is an indispensable basic component for achieving precise control of industrial automation.


Specification parameters

(1) Channel parameters

Number of channels: Equipped with 8 analog input channels, it can simultaneously access 8 different analog signals, suitable for small and medium-sized industrial automation data acquisition scenarios, meeting diverse monitoring needs.

Signal type: Supports multiple standard analog signal inputs, including 4-20mA current signals, ± 10V voltage signals, etc. 4-20mA current signal is commonly used for long-distance signal transmission in industrial sites, with strong anti-interference ability; The ± 10V voltage signal is suitable for situations where high signal accuracy is required and the transmission distance is close.

(2) Electrical parameters

Input accuracy: With high input accuracy, usually up to ± 0.1% FS (full range), it can accurately collect analog signals, effectively reduce measurement errors, ensure the accuracy of collected data, and provide reliable data support for industrial control.

Input impedance: For current input, the input impedance is generally less than 250 Ω; For voltage input, the input impedance is greater than 10M Ω. A reasonable input impedance design can ensure that the signal is not distorted during transmission and ensure the stability of signal acquisition.

Isolation characteristics: Electrical isolation design is adopted between channels and between channels and systems, with an isolation voltage of up to 500V AC, effectively preventing signal interference and electrical faults from affecting each other, improving the reliability of module operation and system safety.

(3) Physical parameters

Size specifications: Adopting a compact design, the external dimensions are approximately [length x width x height, such as 80mm x 50mm x 40mm (depending on the actual product)], making it easy to install in control cabinets, distribution boxes and other equipment with limited space, saving installation space and improving system integration.

Installation method: Supports standard DIN rail installation, the installation process is simple and fast. Simply insert the module into the guide rail and secure it, and the installation can be completed. It can also be fixed to the installation plane with screws, making it convenient for on-site installation and later maintenance.

Environmental adaptability: The working temperature range is generally -25 ℃ to+60 ℃, and the relative humidity range is 5% -95% (without condensation). It has good resistance to vibration, impact, and electromagnetic interference, and can operate stably in harsh industrial sites such as high temperature, humidity, high dust, and complex electromagnetic environments.


Introduction

This section explains the inputs, control logic, communication, and connections for the IMASI23 module.
The ASI module interfaces 16 analog inputs to a Harmony controller.
The Har mony controller communicates with its I/O modules over the I/O expander bus (Fig. 1-1). Each I/O module on the bus has a unique address set by its address dipswitch (S1)


Module Description

The ASI module consists of a single printed circuit board that occupies one slot in a module mounting unit (MMU).
Two cap tive latches on the module front panel secure it to the module mounting unit.
The ASI module has three card edge connectors for external signals and power: P1, P2 and P3. P1 connects to the supply voltages. P2 connects the module to the I/O expander bus, over which it communicates with the controller.
Connector P3 carries the inputs from the termination cable plugged into the termination unit (TU). The terminal blocks for field wiring are on the termination unit.
A single dipswitch on the module sets its address or selects onboard tests. Jumpers configure the type of analog input signals.


Functional Operation

The ASI module is an intelligent module with an onboard microcontroller and memory.
It interfaces to a controller over the I/O expander bus.
An onboard microcontroller allows the ASI module to perform the input channel processing.
This allows the controller to do other tasks. Input processing tasks include error compensation, adjustments, and conversion to engineering units.
Each channel provides underrange, overrange, and open input detection.
Onboard circuitry detects either open field wires or a disconnected termination unit cable. Open input detection is provided for millivolt, thermocouple, RTD, 1 to 5 VDC, and 4 to 20 milliampere input types and can detect any combination of  open input wires.
Figure 2-1 shows a block diagram of the IMASI23 module.


Isolated A/D Converter

Each input channel has an A/D converter (delta-sigma type).
Isolation is done by DC/DC converters (one per channel) and optocouplers on the digital serial line of the A/D converter.
Each channel accepts voltage and resistance inputs. Resis tance measurements are made by digitizing the voltage drop created across the input resistance source.
A precision constant current source supplies the current used to measure the input.


Cold Junction Reference

The ASI module measures the cold junction RTDs on the termination unit of the analog input module. 

This results in an accurate reading of the ambient temperature at the field wire termination area.

This value can be used by the ASI module to compensate for voltages generated from the bimetal
connections made by terminating the field wires (thermocouple wires) onto the terminal blocks of the termination unit.
The block address of the cold junction reference used by ther mocouple inputs on the ASI module is contained in FC 215, specification S3.

Each analog input module configured for a thermocouple input requires a cold junction reference. 

Each analog input module can only have one reference which can be used by up to 16 thermocouple inputs.

The exception to this is when one of the inputs is used as a remote cold junction reference.


Refer to Section 4 for more information

Digital Input Multiplexer (MUX)

Once isolated, digitized, and buffered, the input signal is sent to the microcontroller by a digital multiplexer. 

All the inputs, including the references and cold junction input, are multi plexed as shown in Figure 2-1.

Microcontroller and Memory
The onboard microcontroller coordinates ASI functions.
The main functions are:
• Channel and cold junction reference switching.
• Programming A/D converters.
• Reading the A/D converters and applying all necessary cor
rection factors.
• Interfacing to switch and LEDs (used for diagnostic mode).
• Background integrity checking.
• Reading and writing expander bus data through dual port


RAM (DPRAM)

Switch Settings
The ASI module has one eight-position dipswitch to select the I/O module address on the I/O expander bus.
This switch also selects built-in diagnostics for stand alone testing LED Indicators
The ASI module has two LED indicators, one red and one green, which show the operating status. The LEDs will:
• Flash red on power-up.
• Remain off (both LEDs) after passing onboard diagnostics until the ASI module is configured by the controller.
• Show solid green after the controlling controller downloads configuration data.
• Show solid green during normal running.
• Blink green when the controller that configured the ASI module enters configure mode from execute mode.
• Blink green if I/O expander bus communication is lost (if the controller is removed).
• Show solid red if a fatal failure of the ASI module occurs.
For example, if power up diagnostics fail.
• Show solid red for a power fail interrupt (PFI).


I/O Expander Bus

The I/O expander bus is a high-speed, synchronous, parallel bus. It provides a path between controllers and I/O modules.
The controller sends control functions to the ASI module, and the ASI module provides input data to the controller.
The P2 card edge of the ASI module and controller connect to the bus.
The I/O expander bus is parallel signal lines located on the module mounting unit backplane.
A 12-position dipshunt placed in a socket on the MMU backplane connects the bus between the controller and I/O modules.
Cable assemblies can extend the bus to eight module mounting units.

A controller and its I/O modules form a subsystem within a Harmony control unit (HCU). 

The I/O expander bus between control and I/O subsystems must be separated.

Leaving a dipshunt socket empty or not connecting the module mounting units with cables separates them


I/O Expander Bus Interface

The ASI module communicates with the controller through a shared memory interface connected to the I/O expander bus.
The ASI module constantly updates the shared memory device (dual port RAM) with the current values of the inputs.
The controller can read these values at any time, even if the ASI module is simultaneously writing to the dual port RAM.
The ASI module uses a custom gate array for the I/O expander bus interface. An integrated circuit holds all the control logic and communication protocol. This integrated circuit provides these functions:
• Address comparison and detection.
• Message decoding and translation.
• Data line filtering of bus signals.
• Onboard bus drivers.
• Expander bus watchdog.
A dual port RAM stores data that can be accessed at the same time by the controller and the I/O module's microcontroller.
Data Values
For all inputs, channel values are adjusted based on the factory calibration. Thermocouple inputs receive cold junction reference compensation. Lead wire resistance adjustments are performed when necessary (for cold junction reference only).
The ASI module provides values to the controller over the I/O expander bus. These values are in engineering units.
The ASI module sends a status indication to the controller for each input channel. This status indicates any hardware errors and channel configuration errors detected by the ASI module.


Termination Units

The IMASI23 module uses one NTAI06 termination unit to connect to field signals. An NKAS01 or NKAS11 cable connects the termination unit to the ASI module through its P3 connector.
The termination unit contains RTDs used for cold junction compensation of thermocouple inputs. They also contain the circuitry needed to convert 4 to 20 milliampere field signals into the 1 to 5 VDC needed to input to the analog input module.
The system power supply is protected from short circuits by fuses on the NTAI06 termination unit.
Function Codes
NOTE: Refer to Appendix C for function code specification changes required when replacing an IMASI03 module with an IMASI23 module.
FCs 215 and 216 in the controller configure the ASI module and identify the active analog inputs. One FC 215 is required for each ASI module.
One FC 216 is required for each input channel used on the ASI module.
These function codes specify the I/O expander bus address of the ASI module and the channel number on the module connected to a specific analog input signal.
The type of the input and the zero and span in engineering units must also be specified to ensure proper scaling and corrections for calibration, cold junction compensation, and nonlinearity correction.
Add FC 215 and 216 to the controller to configure the ASI module. Set FC 217 in the controller to calibrate the ASI module or to set the user gain and offset values.
Refer to the Composer Function Code Application Manual for more information.

IMASI23 ABB Analog Input Module,TC,MV,RTD.



  • Rexroth HCS02.1E-W0028-A-03 CSH01.1C-PB Drive Package
  • Bosch Rexroth VT-VARAP 1-537-20/V0 Amplifier
  • Bosch Rexroth PPC-R02.2N R911285402 Control Unit
  • National Instruments PCI-7342 Motion Controller
  • National Instruments PXIe-6535 Digital I/O Module
  • National Instruments PCIe-6738 Analog Output Card
  • National Instruments NI-6583 Digital I/O Adapter Module
  • National Instruments NI TB-9214 Terminal Block
  • National Instruments NI 9222 Simultaneous Analog Input Module
  • National Instruments PXIe-8364 MXI-Express Module
  • National Instruments PXI-8185 Embedded Controller
  • National Instruments PCI-1405 Device
  • National Instruments SCXI-1160 Module
  • National Instruments PCI-MIO-16E-1 Device
  • National Instruments USB-6216 Device
  • National Instruments PXIe-2543 Module
  • National Instruments PCI-5102 Digitizer
  • National Instruments PXI-6284 DAQ Device
  • National Instruments PXI-7330 Controller
  • National Instruments cFP-2100 Controller
  • National Instruments USB-6002 DAQ Device
  • National Instruments PCIe-6374 Multifunction DAQ Card
  • National Instruments PXIe-4610 Power Amplifier Module
  • National Instruments PXIe-4154 Battery Simulator
  • National Instruments PXIe-7858R Reconfigurable I/O Module
  • National Instruments BNC-2090A BNC Terminal Block
  • National Instruments cRIO-9066 CompactRIO Controller
  • National Instruments 198944C-04L Ordering Part Number
  • National Instruments 157732A-02L Ordering Part Number
  • National Instruments TC-4353 Thermocouple Terminal Block
  • National Instruments 190996F-04L PCI-6250 DAQ Part Number
  • National Instruments PCI-7334 Controller
  • National Instruments TRC-8542 Cable
  • National Instruments CAP-1804 Accessory
  • National Instruments myRIO-1900 Kit
  • National Instruments PCI-AI16HR Board
  • National Instruments PCIe-6341 Device
  • National Instruments PXI-6514 Module
  • National Instruments PXI-6025E DAQ Card
  • National Instruments DAQPad-6015 Device
  • National Instruments BNC-2090 Accessory
  • National Instruments USB-4431 Dynamic Signal Module
  • National Instruments 181045-02 Ordering Part Number
  • National Instruments 779697-02 Ordering Part Number
  • National Instruments cFP-AI-112 Analog Input Module
  • National Instruments PCI-6602 Counter Timer Card
  • National Instruments NI-9871 RS485 Interface Module
  • National Instruments NI 9238 Voltage Input Module
  • National Instruments USB-6001 USB-6008 DAQ Devices
  • National Instruments PXI-6289 Multifunction DAQ Card
  • National Instruments PCI-7340 Motion Controller
  • National Instruments PCI-6036E DAQ Device
  • National Instruments USB-6002 DAQ Device
  • National Instruments NI-9201 Module
  • National Instruments SCXI-1531 Module
  • National Instruments 779351-01 Module
  • National Instruments PCI-6071E DAQ Device
  • National Instruments PCI-8512 Device
  • National Instruments NI 9375 I O Module
  • National Instruments PCI-8431/2 Card
  • National Instruments PXI-4472 Module
  • National Instruments PXI-6527 Digital Module
  • National Instruments PXI-7344 Motion Controller
  • National Instruments 779553-50 Ordering Part Number
  • National Instruments PXI-6040E Multifunction DAQ Module
  • National Instruments PCI-6013 Multifunction DAQ Card
  • National Instruments SCB-68 Shielded Connector Block
  • National Instruments PXI-7350 Motion Controller
  • National Instruments PXI-5142 Digitizer Oscilloscope Card
  • National Instruments 781157-01 Ordering Part Number
  • National Instruments cRIO-9057 CompactRIO Controller
  • National Instruments NI 9881 Module
  • National Instruments USB-8506/2 Device
  • National Instruments PCIe-8255R Device
  • National Instruments NI 9218 Module
  • National Instruments TB-2709 Terminal Block
  • National Instruments PXIe-1075 Chassis
  • National Instruments PCI-6254 DAQ Device
  • National Instruments FP-1000 Network Module
  • National Instruments 780876-01 Output Module
  • National Instruments PXI-6225 DAQ Module
  • National Instruments FW-7344 Motion Controller
  • National Instruments PCI-488.2 GPIB Interface Card
  • National Instruments PXIe-4300 Analog Input Module
  • National Instruments PXIe-8360 MXI-Express Interface
  • National Instruments SCXI-1120 Isolated Amplifier Module
  • National Instruments PCIe-6341 DAQ Device
  • National Instruments PXI-6723 Module
  • National Instruments PXI-5404 Source
  • National Instruments SH200LF Switch Cable
  • National Instruments PCI-6023E DAQ Card
  • National Instruments TB-4302C Terminal Block
  • National Instruments PXI-8430/2 Module
  • National Instruments 779892-02 Module
  • National Instruments QNET-04838 Actuator Board
  • National Instruments NI 9871 RS485 Interface Module
  • National Instruments PCI-6250 Multifunction DAQ Card
  • National Instruments cDAQ-9188 Ethernet Chassis
  • National Instruments PXI-5441 Arbitrary Waveform Generator
  • National Instruments MID-7604 Motion Interface Device
  • National Instruments FP-DO-403 Digital Output Module
  • National Instruments cRIO-9114 Reconfigurable Chassis
  • National Instruments SCXI-1126 Frequency Input Module
  • National Instruments 776572-60 Ordering Part Number
  • National Instruments PCI-7332 Motion Control Card
  • National Instruments NI-9217 RTD Input Module
  • National Instruments PCI-6023E Multifunction DAQ Card
  • National Instruments PXI-6650H Timing Module
  • National Instruments PXI-8196 Embedded Controller
  • National Instruments PXI-6528 Isolated Digital I/O Board
  • National Instruments PXI-6120 Simultaneous DAQ Card
  • ALSTOM 029.204 687 Digital I/O VME Board
  • National Instruments PXI-6509 Digital I/O Module
  • National Instruments FP-AI-112 Analog Input Module
  • National Instruments cRIO-9065 CompactRIO Controller
  • National Instruments PXI-2570 SPDT Relay Module
  • National Instruments PXI-5610 Module
  • National Instruments cFP-RTD-122 Module
  • National Instruments PXI-8336 Module
  • National Instruments NI 9237 Module
  • National Instruments PCI-6224 DAQ Card
  • National Instruments USB-6218 DAQ Device
  • National Instruments PCI-6601 Device
  • National Instruments SCXI-1124 Module
  • National Instruments USB-6525 DIO Device
  • National Instruments cDAQ-9189 Chassis
  • National Instruments PXIe-8394 MXI Module
  • National Instruments PXIe-4112 Power Supply