GE Fanuc 531X160HFCACG1 Controller Encoder Process Board

GE Fanuc 531X160HFCACG1 Controller Encoder Process Board

Model:531X160HFCACG1 Type:Encoder Process Board Application:Industrial Control Systems Power Consumption:12W Operating Temperature:-40"C to +85"C Dimensions:100mm x 85mm x 30mm Weight:0.18kg Connectivity:RS-232, RS-485 Protocol Compatibility:EtherCAT, DeviceNet, Profinet The GE FANUC 531X160HFCACG1 is an essential component for enhancing the accuracy and reliability of your motion control systems. Engineered with a high-performance microprocessor, this board ensures smooth and precise operation under various environmental conditions. Featuring a wide operating temperature range from -40"C to +85"C, it is suitable for both indoor and outdoor industrial applications.

 Its robust design withstands extreme temperatures, ensuring continuous performance in harsh environments. With support for multiple communication interfaces including RS-485, CANopen, and Ethernet, the board facilitates seamless integration with a variety of control systems. This flexibility allows for easy setup and compatibility with different automation solutions. The board  efficient power consumption keeps operational costs low while maintaining high performance. 

It is specifically tailored for use with GE FANUC  Mark VI series PLCs, offering optimized performance and reliability in complex control scenarios. Manufactured with precision and durability in mind, the GE FANUC 531X160HFCACG1 Controller Encoder Process Board is a reliable choice for upgrading or expanding your industrial automation capabilities. It delivers enhanced precision, improved system efficiency, and greater operational stability, making it an indispensable addition to any modern industrial setup. This high-performance Encoder Process Board is designed to enhance the precision and reliability of industrial control systems, providing critical feedback for accurate motion control applications. 

Compatibility 

ƒ Compatible with any Series 90-30 CPU except IC693CPU321 and IC693CPU340. Configuration size is limited for CPU311/313/331, as described on the next page. 

ƒ Requires release 8.0 CPU firmware. The latest Release 10 is recommended, if available for the particular CPU. 

ƒ Requires CIMPLICITY Machine Edition Logic Developer PLC version 3.0 plus the appropriate service pack or special (or a version later than 3.0). 

ƒ Not compatible with the VersaPro™, Control, or Logicmaster™ programming software. 

ƒ The Series 90-30 Hand-Held Programmer (IC693PRG300) cannot be used to configure this module. New Features The Series 90-30 DeviceNet Master Module allows a Series 90-30 PLC to send and receive I/O data from a DeviceNet network. 

Module features include: 

ƒ Support for all standard data rates (125K, 250K, 500K) 

ƒ Support for 255 bytes input data transfer and 255 bytes output data transfer per slave 

ƒ Support for 3972 bytes of input data transfer and 3972 bytes of output data transfer per master 

ƒ Support for two I/O connections per Slave - Typically one connection is used for Polled and the other is used for Strobe, Cyclic, or COS 

ƒ Support for Poll, Strobe, Cyclic and COS I/O Connections, Fragmented I/O and Explicit Messaging 

ƒ Support for Unconnected Message Manager (UCMM) with 1 proxy connection per slave device 

ƒ Support for configuration of the global scan rate 

ƒ Support for configuration of update rates for Poll and COS/Cyclic on a connection basis 

ƒ Support for PLC-application initiated explicit messaging via a COMMREQ 

ƒ Master can be configured to operate as a slave simultaneously with master operation 

ƒ Configurable fault behavior on loss of communication 

ƒ Reports loss or reestablishment of communication with slaves in PLC fault table (configurable) 

ƒ Support for 64 network device status bits (note: the bit for the master itself is always zero) 

ƒ Firmware update via service port on module