GE FANUC 531X300CCHAFM5 Industrial Control Card

GE FANUC 531X300CCHAFM5 Industrial Control Card

Processor Speed:96 MHz Memory Type:32-bit, Floating Point Operating Capacity:512 Kb (Low Speed) Interface Compatibility:RS-232, RS-485 Operating Temperature Range:-20"C to +60"C Power Consumption:12 VDC The GE Fanuc 531X300CCHAFM5 Control Card is a pivotal component for modern industrial drive systems, offering unparalleled performance and reliability in diverse manufacturing sectors. Designed with cutting-edge technology, it ensures seamless integration into existing systems, providing superior control over machinery operations. Engineered with a high-speed 96 MHz processor and 512 Kb of low-speed memory, this control card efficiently manages complex operations, ensuring smooth and precise control. Its 32-bit floating-point processing capability optimizes performance across a wide range of applications. 

 This control card is equipped with six diagnostic LEDs, enabling users to monitor system health in real-time. These features are crucial for predictive maintenance, helping prevent unexpected downtimes and reducing maintenance costs. For enhanced safety and system integrity, the GE Fanuc 531X300CCHAFM5 Control Card incorporates advanced diagnostic and protection mechanisms. These safeguards are critical in safeguarding investments in high-impact industrial equipment. With factory-drilled corners for straightforward installation and compatibility with the DC-300 drive and other GE general purpose drive systems, this control card streamlines integration processes, making it an indispensable upgrade for facilities looking to optimize their industrial drive systems. The GE-FANUC 531X300CCHAFM5 Control Card is a specialized component designed for high-power, flexible, and user-friendly industrial drive systems. This card serves as a critical component in managing the operations of GE-FANUC  DC-300 drive and other general-purpose systems.  

Compatibility 

ƒ Compatible with any Series 90-30 CPU except IC693CPU321 and IC693CPU340. Configuration size is limited for CPU311/313/331, as described on the next page. 

ƒ Requires release 8.0 CPU firmware. The latest Release 10 is recommended, if available for the particular CPU. 

ƒ Requires CIMPLICITY Machine Edition Logic Developer PLC version 3.0 plus the appropriate service pack or special (or a version later than 3.0). 

ƒ Not compatible with the VersaPro™, Control, or Logicmaster™ programming software. 

ƒ The Series 90-30 Hand-Held Programmer (IC693PRG300) cannot be used to configure this module. New Features The Series 90-30 DeviceNet Master Module allows a Series 90-30 PLC to send and receive I/O data from a DeviceNet network. 

Module features include: 

ƒ Support for all standard data rates (125K, 250K, 500K) 

ƒ Support for 255 bytes input data transfer and 255 bytes output data transfer per slave 

ƒ Support for 3972 bytes of input data transfer and 3972 bytes of output data transfer per master 

ƒ Support for two I/O connections per Slave - Typically one connection is used for Polled and the other is used for Strobe, Cyclic, or COS 

ƒ Support for Poll, Strobe, Cyclic and COS I/O Connections, Fragmented I/O and Explicit Messaging 

ƒ Support for Unconnected Message Manager (UCMM) with 1 proxy connection per slave device 

ƒ Support for configuration of the global scan rate 

ƒ Support for configuration of update rates for Poll and COS/Cyclic on a connection basis 

ƒ Support for PLC-application initiated explicit messaging via a COMMREQ 

ƒ Master can be configured to operate as a slave simultaneously with master operation 

ƒ Configurable fault behavior on loss of communication 

ƒ Reports loss or reestablishment of communication with slaves in PLC fault table (configurable) 

ƒ Support for 64 network device status bits (note: the bit for the master itself is always zero) 

ƒ Firmware update via service port on module