GE DS200PANAH1A Gas Turbine Control Board

GE DS200PANAH1A Gas Turbine Control Board

Part Number DS200PANAH1A Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark V Function Module Availability In StockDS200PANAH1A is an ARCNET LAN Driver Board developed by GE under Mark V series. COREBUS and Stage Link may communicate through ARCNET thanks to the LAN Driver Board (PANA). PANA attaches to both AAHA boards via its APL and BPL connections and is housed as a daughterboard on the LBC586P board in R. Through its P1 and P2 bus connectors, the PANA board transmits data to the Control Engine LBC586P processor board. 

In position 1 of R, there is one PANA board. DS200PANAH1A Connectors Link between the AAHA1 board and APL-ARCNET for communication. Communication with the AAHA2 board through BPL-ARCNET. Bus connection to the LBC586P board through pin P1. Bus connection to the LBC586P board through pin P2. DS200PANAH1A Configuration Hardware The COREBUS and Stage Link ARCNET addresses for the R core are set using the four switches on the PANA board. The first two are for Stage Link, and the second two are for Channel B. (COREBUS). Each ARCNET channel's interrupt, I/O, and memory addresses are configured via hardware jumpers. All of these internal software options are factory-specific. It is important to confirm that the hardware jumper settings on replacement boards are identical to those on the original board. 

 Software The PANA board uses no software configuration. DS200PANAH1A Features One 40-pin connector, ten jumpers, and one 64-pin connector are among the features. Two RF FET semiconductor devices are also included on the GE ARCNET No-LAN LM Gas Turbine Control Board to amplify and modify the signal. The board, which is 3.75 inches square, is made to be mounted to the board rack located inside the drive. The holes in the board's corners line up with the corresponding holes in the board rack. Installing the replacement board requires using the screws that held the broken board to the rack. 

Use a screwdriver to remove the screws before removing the damaged board, and hold the screws with the other hand. Remove the screws from the drive without dropping them. The default settings for the 10 jumpers are predetermined at the factory. Installation The jumpers can be customized by the installer at the initial installation so that the board will handle information as needed by the site. The installer cannot alter some jumpers since they are factory-set. Exclusively one position is supported, and they are only used for testing on the assembly line. The jumpers have special identification numbers with the prefix JP. Examine the faulty board and note the jumper positions and identifications. You must set all 10 jumpers exactly where they are in the original board in order for the replacement to be configured to function identically.

This DS200PANAH1A printed circuit board product offering was originally manufactured for placement in General Electric's Mark V Turbine Control System Series. As you have surely been able to ascertain by its full extended series name, the Mark V Series that this DS200PANAH1A printed circuit board or PCB for short belongs to has specific applications in the management and control systems of compatible steam, wind, and gas turbine automated drive assemblies, and is considered a General Electric legacy series due to its manufacture discontinuation in the years following its initial release. This DS200PANAH1A PCB's Mark V Turbine Control System Series, while known as a General Electric legacy series, is also one of the final General Electric Mark series to make use of their patented Speedtronic control system technology. This DS200PANAH1A PCB is better-known as an ARCNET LAN Driver Board, although the original product of this functionality developed for the Mark V is the DS200PANAH1 parent printed circuit board missing this DS200PANAH1A product's A-rated functional product revision.

Hardware Tips and Specifications

This DS200PANAH1A product offering makes use of its own series of hardware component inclusions and specifications confirming its functional status as an ARCNET LAN Driver Board. The GE ARCNET No-LAN LM Gas Turbine Control Board DS200PANAH1A  features one 40-pin connector, 10 jumpers, and one 64-pin connector. The GE ARCNET No-LAN LM Gas Turbine Control Board DS200PANAH1A also has two RF FET semiconductor devices to amplify and adjust the signal. The board is 3.75 inches square in size and it is designed to be attached to the board rack inside the drive. The holes in the corners of the board align with the matching holes in the board rack. Use the screws that attach the defective board to the rack to install the replacement. When you remove the defective board use a screwdriver to loosen the screws and with the other hand hold the screws. Without dropping the screws, remove them from the drive. As with many General Electric printed circuit board product offering available to our new and reconditioned inventory; this DS200PANAH1A product interfaces with other Mark V Series printed circuit boards through use of a varied series of General Electric connectors. Some of the crucial connectors in this DS200PANAH1A PCB's assembly include:

The APL AAHA1 Board ARCNET Connection Link

The BPL AAHA2 Board ARCNET Connection Link

The P1 LBC586P Board Bus Connection

The P2 LBC586P Board Bus Connection