GE DS2020FECNRP010A Field Exciter Module

GE DS2020FECNRP010A Field Exciter Module 

Part Number DS2020FECNRP010A Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VI/VIe Function Module Availability In StockThe field exciter DS2020FECNRP010A belongs to the Mark V series. The GE Field Exciter Board DS2020FECNRP010A has seven jumpers and two terminal blocks, each with three terminals. JP1 through JP7 are the names of the jumpers. Multiple prong-type connectors are also included on the GE Line Protection Board DS2020FECNRP010A. The board is mounted on standoffs on another drive component. The signal wires that connect the board to the component to which it is connected begin on the component to which it is attached. 

The drive is a high-voltage device that, if not used properly, can cause serious injury. Electrical burns and shock can result from the electrical energy, and the powerful moving parts might injure people in the proximity. As a result, personnel who service and maintain the drive must have a basic understanding of the drive's hazards and how to avoid difficulties. First, inspect the surrounding area before handling the drive or any components inside the drive. Make sure there is no dampness, oil, or grease on the floor. Water is an electrical conductor and can cause significant injury. 

Before you begin, make sure there is no wetness on the floor and that it is fully dry. If moisture is a persistent problem, dehumidifiers may be required on-site to prevent condensation. Detergents can be used to remove oil and grease from the floor. Remove any ungrounded electrical cords as well, as they are a fire hazard. Always keep in mind that the drive may have many power sources connected to it, and that you should always check for power before touching any components.

The Series 90* -30 CPU374 PLUS provides a built-in enhanced Ethernet interface that  provides TCP/IP communications with: 

▪ Series 90, PACSystems, and VersaMax PLCs 

▪ Host computers running the Host Communications Toolkit or CIMPLICITY software 

▪ Computers running the TCP/IP version of the programming software CPU Features  

▪ High speed Boolean and non-Boolean processing provided by a 586-class 133MHz  processor 

▪ Two Ethernet ports: 10/100 Mbytes (one IP address) with a built-in, auto-sensing  Ethernet switch 

▪ Support for EZ Store Device allows you to download a program without a PC 

▪ 240KB of user memory Key Ethernet Features 

▪ Full PLC programming and configuration services 

▪ Periodic data exchange using Ethernet Global Data (EGD) and EGD commands to  read and write PLC and EGD exchange memory over the network 

▪ TCP/IP communication services using SRTP 

▪ Support for SRTP Client (Channels) 

▪ Modbus/TCP Server, supporting Modbus Conformance classes 0, 1, and 2. 

▪ Modbus/TCP Client, supporting Modbus Conformance classes 0, 1, and Function Codes 15, 22, 23, and 24 for Conformance class 2. 

▪ Remote PLC monitoring from a web browser 

▪ Comprehensive station management and diagnostic tools

Instructions and warnings related to the operation of the product:

The following specifications must be strictly observed:

 The technical specifications and typical applications of the product system must be strictly observed.

 PERSONNEL TRAINING: Only trained personnel may install, operate, maintain or repair the product system. These personnel must be instructed on the

These personnel must be instructed and briefed on the conditions in the hazardous area.

 Unauthorised modifications: No modifications or structural changes may be made to the product system.

 Maintenance Responsibility: It must be ensured that the product system is used only under appropriate conditions and in a condition fully suitable for use.

 Working environment: The user must fulfil the specified environmental conditions:

Safety regulations

The following safety regulations must be fully observed when (maintenance) work is carried out on the product system:

1 Disconnect completely.

2 Secure to prevent reconnection.

3 Confirm that the installation has been completed.

4 Perform grounding and short-circuiting.