GE DS215KLDCG1AZZ03B Power Connect Board

GE DS215KLDCG1AZZ03B Power Connect Board

Part Number DS215KLDCG1AZZ03B Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VI/VIe Function Module Availability In StockDS215KLDCG1AZZ03B is a Power Connect Board developed by GE. It is a part of Mark V Series. The board includes specific firmware that supports its operation and ensures compatibility with other system components. Firmware updates may be necessary to maintain optimal performance. Connectors and Interfaces: Equipped with various connectors, facilitates easy connections to other boards and components within the control system. Keypad Removal Procedure Preliminary Steps: If replacing a C revision board, skip directly to board removal. 

Remove Bezel and Components: Remove the screws securing the bezel, then take off the bezel, gasket, and overlays. Remove Keypad Screws: Unscrew the ten inner screws holding the keypad. Avoid removing the outer screws to prevent the unit from falling out of the enclosure. Carefully pry up the keypad from the top. Disconnect Connections: Lift the keypad and disconnect the lKPL, 2KPL, and 3KPL connectors from the display board. Keypad Installation Procedure Reinstall Keypad: Reverse the removal steps, but do not reconnect the lKPL, 2KPL, and 3KPL connections until the new display board is installed. Display Board Removal Procedure Access Board Holder: Open the unit to access the plastic board holder.

Release Board Holder: Unlock the two retainer latches of the board holder, then lift and pull out the board holder to access the display board. Disconnect Connectors: Disconnect the 3PL, lKPL, 2KPL, and 3KPL connectors. Remove the display board held by six plastic clips. Display Board Installation Procedure Install Replacement Board: Place the new board in the board holder, ensuring it is securely held by the plastic clips. Reconnect Connectors: Reattach the 3PL, lKPL, 2KPL, and 3KPL connectors. Secure Board Holder: Slide the board holder back into its position and lock it with the two retainer latches. Close Unit and Test: Close up the unit, restore power, and run the KY/LED/DSP LOCAL MODE UTILITY test to verify the correct installation and operation of the new board.

ABOUT THE DS215KLDCG1AZZ03B

General Electric created the DS215KLDCG1AZZ03B PC Board to be a part of the Mark V Speedtronic turbine control line. This board is now a legacy series part and may be hard to find, but AX Control attempts to keep this board in stock, as with any Mark V Series product in our new and reconditioned inventory. Before making an ultimate purchase decision on this DS215KLDCG1AZZ03B Power Connect Board, it is crucial to realized its statuses, both as a General Electric printed circuit board with a special assembly type, and as a Mark V Series PCB that comes with an optional firmware package.

Hardware Tips and Specifications

The DS215KLDCG1AZZ03B is a large PCB (printed circuit board) that weighs right around 1.07 lbs. This board comes with firmware, as mentioned above and reinforced through the inclusion of the AZZ03B tag in its DS215KLDCG1AZZ03B functional product number. This DS215KLDCG1AZZ03B product number is actually a very useful source of hardware specification information for this rather mysterious Mark V Series product, revealing details such as:

A DS215 special assembly

The KLDC functional acronym

A normal style of PCB protective coating

A group one Mark V Series grouping

An A-rated functional product revision

The ZZ03B optional firmware package

There are a lot of parts that form a DS215KLDCG1AZZ03B Power Connect Board, and that are visible upon a simple visual inspection. On the top half of the board are a total of twenty-one relays. There are also three yellow capacitors, ten small yellow diodes, and three yellow resistor networks. There are six integrated circuits, eight white LEDs, and an inductor coil that is flanked by two transistors (one on the left and one on the right.) On the bottom half of the board are twenty-four additional LED lights, eleven integrated circuits, a processor, two EPROMS, nineteen yellow resistor networks,  thirty-four small yellow diodes, four yellow capacitors, three large brown resistors, six small brown resistors, two green resistors, and an oscillator crystal. This board also has eight factory-drilled holes that can be used to install the card; these holes are equidistantly placed in the four corners of the board and along the four edges.