GE DS3800HITA Printed circuit board

GE DS3800HITA Printed circuit board 

Part Number DS3800HITA Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VI/VIe Function Module Availability In StockDS3800HITA is an I/O control card developed by GE. It is a part of Mark IV control system Features A through J are labeled along the top edge of the card, with marks between each letter for alignment. One AMP connector, marked 218A4553-1 AMP 533002-1 8442, occupies the board's left edge. The board's top right edge has nine LEDs. Eight are labeled 0-7 in red, and one is labeled IMOK in amber. The bottom right edge of the board has fifteen test points. 1-7, OX, VA, VB, VC, OUT0, OUT1, OUT2, DCOM are the labels for these. On the board, there are seven jumpers. 

Jumpers 1-5 form a line and can choose A or B. Jumper 6 is located near the LEDs in the upper right corner of the board and has the option of SHORT or LONG. Jumper 7 is near the top left of the board and has an ON/OFF switch. Operator Interface Module The primary interface with the control is through the Operator Interface Module. A photograph of the module can be found in Figure V-A-l. The module is mounted on the left front door and is functionally divided into two sides: one that interfaces with the Video Display, [CRT], and one that interfaces with the control. The operator pushbuttons are shown on the lower right. 

A graphic mylar overlay covers a 7 X 4 matrix of membrane switches, assigning a function to each switch and "blacking out" unused switches. An HPIB card connects the switches and Communicator [C], as well as the Controllers [R], [S], and [T]. When a switch is pressed, an audible acknowledgement of the command is provided by a beeper, and a red LED begins to blink. After three (3) seconds, the operator must confirm the command by pressing the EXECUTE button in the lower left hand corner. If this button is not pressed quickly enough, the red LED will stop blinking and the control will wait for another command.

ABOUT THE DS3800HITA

The DS3800HITA is a printed circuit board manufactured by GE as part of the Mark IV/Speedtronic series. The DS3800HITA has been designed as an Input/Output (I/O) control board.

The specifications of the DS3800HITA are as follows:

factory drilled on all four corners of the card.

labeled at the top edge of the card A through J, with marks between each letter for alignment.

The left edge of the board is taken up by one AMP connector, marked 218A4553-1 AMP 533002-1 8442.

top right edge of the board has nine LEDs. Eight are red, labeled 0-7, and one is amber, labeled IMOK.

bottom right edge of the board consists of fifteen test points. These are labeled 1-7, OX, VA, VB, VC, OUT0, OUT1, OUT2, DCOM.

seven jumpers located on the board. Jumpers 1-5 are in a line and have the option of A or B. Jumper 6 is located in the upper right of the board near the LEDs and has the option of SHORT or LONG. Jumper 7 is located near the top left of the board and has the option of ON or OFF.

has 4 resistor networks located on the board

Our Main Brands

· - ABB Advant-800xA，Advant OCS，Bailey Infi 90 and Net 90，H&B Freelance 2000，DSQC Robots，IGCT / IGBT

· - GE General Electric Field Control, Genius I/O, QuickPanel, RX3i PacSystem, Series 90, Series 90, Series VersaMax

· - Allen Bradley Allen-Bradley SLC500, MicroLogix, CompactLogix, ControlLogix, PLC-5, Panel View,

· - Bently Nevada 3300 System, 3500 System

· - Honeywell 7800 Series, FSC, IPC, Mxopen, TDC 2000, TDC 3000, Experion PKS(C200,C300)

· - Yokogawa Centum CS - Centum VP, Centum XL - micro XL, FA-M3, ProSafe-PLC

· - Ovation, Foxboro, EPRO, Emerson DeltaV, Fuji, Siemens, HIMA, Prosoft, Invensys Triconex, ICS TRIPLEX, Woodward, Bachmann, Schneider