DS3800HRCA | General Electric Signal Condition Processor Board Mark IV

DS3800HRCA | General Electric Signal Condition Processor Board Mark IV

Product Description P/N: DS3800HRCADescription / Specifications DescriptionThe DS3800HRCA is a Signal Condition Processor Board from General Electric鈥檚 Speedtronic Mark IV Turbine Line. It functions as a processing daughter board, connecting via a long female power terminal, two clips, and two small screws. The board is labeled along one edge with letters for identification.

Technical SpecificationsPart Number DS3800HRCAManufacturer General ElectricType Signal Condition Processor BoardLine Speedtronic Mark IV Turbine LineConnections Long female power terminal, two clips, two small screwsEdge Labeling Labeled with lettersLEDs 1 amber LED, 4 red LEDsLED Mounting Held with small black clipsJumper Prongs 5 prongs with 2 coversCapacitors 5 yellow capacitorsDiodes 3 blue diodes, 2 silver diodes, 1 black diode, 19 yellow diodesResistors 16 banded resistorsInformation About DS3800HRCAThe DS3800HRCA is a Signal Condition Processor Board manufactured by General Electric, designed for use in the Speedtronic Mark IV Turbine Line. This board functions as a processing daughter board and connects via a long female power terminal, two clips, and two small screws. The board is labeled along one edge with letters for identification.The DS3800HRCA features one amber LED and four red LEDs, with each LED secured in place by small black clips.

 Additionally, the board includes five jumper prongs covered by two protective covers, which facilitate adjustments to energy flow. The board is populated with five yellow capacitors, three blue diodes, two silver diodes, one black diode, and nineteen yellow diodes. It also contains sixteen banded resistors, with the bands indicating the current capacity of each resistor.The DS3800HRCA incorporates thirty-three EPROM memory chips, which are programmable and can be updated. Additionally, the board includes four EEPROMs, which are non-volatile memory chips that cannot be updated. EPROMs and EEPROMs are visually similar, but EPROMs can be identified by a small circle on the top, distinguishing them from EEPROMs.Manufacturer informationGeneral Electric (GE) is a multinational conglomerate founded in 1892, based in the United States.

 It operates in various industries, including aviation, healthcare, renewable energy, and power. GE is known for its innovations in technology, manufacturing, and infrastructure solutions.IQElectro is not an authorized distributor.QElectro LLC (IQElectro) is NOT an Authorized Distributor or in any way affiliated with Rockwell Automation, Siemens, or any other Manufacturers. IQElectro is NOT an Authorized Dealer of this product. The product may be of older version, date codes, or design than that available from authorized dealers. As IQElectro is not an authorized dealer of this product, the Original Manufacturer's Warranty and Support DO NOT apply.IQElectro sells SURPLUS onlyand DOES NOT SELL SOFTWARE or FIRMWARE licenses For more detailed information, please refer to the full version of our disclaimer policy Disclaimer Policy.

Features 

 Single-Slot Module 

 SNP/SNP-X Protocol (master, slave) 

 CCM Protocol (master, slave, peer) 

 RTU Modbus Protocol (slave only) 

 Supports connection to MS-DOS or Windows

 programming and configuration software package (monitor only) 

 12 Mhz, 80C186 Microprocessor 

 Two RS-422/RS-485 or RS-232 Serial Ports 

 CCM, RTU and SNP/SNP-X Available on Either or Both Ports 

 Simultaneous Communications on Both Ports (up to 9.6 Kbps, or 19.2 Kbps individually) 

 High Performance Access to PLC Memory 

 Three Status LEDs 

 Reset pushbutton 

 Soft Switch Configuration (no switches or jumpers) 

 No Battery Required