GE DS3800NPAC CIRCUIT BOARD

GE DS3800NPAC CIRCUIT BOARD

Part Number DS3800NPAC Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VI/VIe Function Module Availability In StockThe DS3800NPAC is a printed circuit board component designed by General Electric for turbine control under Mark IV. The Mark IV is a turbine system from the Mark series. It controls and automates the processes of gas and steam turbines. Fuels are managed according to the turbine system's speed and load management demands. The control system regulates cooling and shutdown, as well as temperature, automated starter, and steam and water injection. The Mark IV safeguards both the turbine and the personnel who operate it and has diagnostics built-in. 

 The diagnostics make the repair and troubleshooting of turbines much easier. The Mark systems have been used to manage turbines since the late 1960s, when the first Mark I system was designed. The Mark systems were built on methods that had been established since the late 1940s. These procedures were created with the use of newly available technology that was introduced over time. The Mark IV system was developed after forty years of operational success and decades of refinement and learning. All of the criteria for managing turbines, as well as the turbine's auxiliary functions, are met by the Mark IV system. 

It makes use of cutting-edge technology at the time. The components include a communicator, which is a device that communicates between the turbine control and the operator interface. If the microprocessor or CRT fails, the system contains a backup LED display.

Features 

 Single-Slot Module 

 SNP/SNP-X Protocol (master, slave) 

 CCM Protocol (master, slave, peer) 

 RTU Modbus Protocol (slave only) 

 Supports connection to MS-DOS or Windows

 programming and configuration software package (monitor only) 

 12 Mhz, 80C186 Microprocessor 

 Two RS-422/RS-485 or RS-232 Serial Ports 

 CCM, RTU and SNP/SNP-X Available on Either or Both Ports 

 Simultaneous Communications on Both Ports (up to 9.6 Kbps, or 19.2 Kbps individually) 

 High Performance Access to PLC Memory 

 Three Status LEDs 

 Reset pushbutton 

 Soft Switch Configuration (no switches or jumpers) 

 No Battery Required

Ease of Use

• Simple and powerful instruction set 

• One-axis or two-axis motion programs with synchronized block start 

• Program support for a short motion program (called Program Zero) which can be created in the MS-DOS programming software configuration function 

• Nonvolatile (flash) storage for 10 programs and 40 subroutines 

• User scaling of programming units (in Standard mode only) 

• Generic programming using command parameters as operands for Acceleration, Velocity, Move and Dwell commands 

• Configured with MS-DOS configuration software 

Our Main Brands

· - ABB Advant-800xA，Advant OCS，Bailey Infi 90 and Net 90，H&B Freelance 2000，DSQC Robots，IGCT / IGBT

· - GE General Electric Field Control, Genius I/O, QuickPanel, RX3i PacSystem, Series 90, Series 90, Series VersaMax

· - Allen Bradley Allen-Bradley SLC500, MicroLogix, CompactLogix, ControlLogix, PLC-5, Panel View,

· - Bently Nevada 3300 System, 3500 System

· - Honeywell 7800 Series, FSC, IPC, Mxopen, TDC 2000, TDC 3000, Experion PKS(C200,C300)

· - Yokogawa Centum CS - Centum VP, Centum XL - micro XL, FA-M3, ProSafe-PLC

· - Ovation, Foxboro, EPRO, Emerson DeltaV, Fuji, Siemens, HIMA, Prosoft, Invensys Triconex, ICS TRIPLEX, Woodward, Bachmann, Schneider