GE DS3800NSCE Speed Current Regulator Board

GE DS3800NSCE Speed Current Regulator Board

Part Number DS3800NSCE Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VI/VIe Function Module Availability In StockDS3800NSCE is a Speed Current Regulator Board developed by GE under Mark IV system. Despite the series being outdated, the GE General Electric Speedtronic Mark IV Gas Turbine Control System remains an enduring and trustworthy solution. This series boasts a resilient and reliable control system that aligns seamlessly with its intended applications. If you're in pursuit of a proven, dependable product that's prepared for immediate dispatch, your search concludes with our comprehensive inventory. Features The board's interior posses two distinct communication conduits, each bearing unique significance. 

A twenty-pin male vertical connector, christened as JA, facilitates the exchange of information vital for the turbine. Akin to a digital synapse, this interface orchestrates the ebb and flow of data. Opposite this, a twelve-pin female connector, denoted as JM, presents a delicate grid a canvas for connectivity that is finely woven to transmit signals with utmost fidelity. Positioned alongside these communication channels are nodes of utility. A solitary TP (test point) beckons to the curious mind, inviting the probing touch of diagnostics. Adjacent to it, a connector point, succinctly labeled as J1, awaits the companionship of cables, an embodiment of connection waiting to be forged. Potentiometers takes center stage, each poised to delicately tweak the harmonious resonance of circuits.

Specifications

Part Number: DS3800NSCE
Manufacturer: General Electric
Series: Mark IV
Function: Speed Current Regulator Board
Product Type: PCB
Availability: In Stock
Country of Manufacturer: United States (USA)

Compatibility 

ƒ Compatible with any Series 90-30 CPU except IC693CPU321 and IC693CPU340. Configuration size is limited for CPU311/313/331, as described on the next page. 

ƒ Requires release 8.0 CPU firmware. The latest Release 10 is recommended, if available for the particular CPU. 

ƒ Requires CIMPLICITY Machine Edition Logic Developer PLC version 3.0 plus the appropriate service pack or special (or a version later than 3.0). 

ƒ Not compatible with the VersaPro™, Control, or Logicmaster™ programming software. 

ƒ The Series 90-30 Hand-Held Programmer (IC693PRG300) cannot be used to configure this module. New Features The Series 90-30 DeviceNet Master Module allows a Series 90-30 PLC to send and receive I/O data from a DeviceNet network. 

Module features include: 

ƒ Support for all standard data rates (125K, 250K, 500K) 

ƒ Support for 255 bytes input data transfer and 255 bytes output data transfer per slave 

ƒ Support for 3972 bytes of input data transfer and 3972 bytes of output data transfer per master 

ƒ Support for two I/O connections per Slave - Typically one connection is used for Polled and the other is used for Strobe, Cyclic, or COS 

ƒ Support for Poll, Strobe, Cyclic and COS I/O Connections, Fragmented I/O and Explicit Messaging 

ƒ Support for Unconnected Message Manager (UCMM) with 1 proxy connection per slave device 

ƒ Support for configuration of the global scan rate 

ƒ Support for configuration of update rates for Poll and COS/Cyclic on a connection basis 

ƒ Support for PLC-application initiated explicit messaging via a COMMREQ 

ƒ Master can be configured to operate as a slave simultaneously with master operation 

ƒ Configurable fault behavior on loss of communication 

ƒ Reports loss or reestablishment of communication with slaves in PLC fault table (configurable) 

ƒ Support for 64 network device status bits (note: the bit for the master itself is always zero) 

ƒ Firmware update via service port on module