GE DS3820PSWA Power Supply Module

GE DS3820PSWA Power Supply Module

Part Number DS3820PSWA Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VI/VIe Function Module Availability In StockDS3820PSWA is a Power Supply Module manufactured and designed by General Electric as part of the Mark IV Series used in GE Speedtronic Gas Turbine Control Systems. A power supply module is an electronic device that provides power to other electronic devices. Some of the key features of a power supply module include: Voltage Regulation: A power supply module must regulate the voltage it supplies to ensure it is within the specified range for the device being powered. Current Limiting: The power supply module must also limit the current it supplies to protect the device being powered from damage due to excess current.

 Efficiency: The efficiency of a power supply module refers to how much of the input power is converted into usable output power. Higher efficiency means less power is wasted as heat, making the device more environmentally friendly. Input Voltage Range: The input voltage range specifies the range of voltages the power supply module can accept as input. Output Voltage Range: The output voltage range specifies the range of voltages the power supply module can provide as output. Protection Features: A power supply module should have protection features like overvoltage protection, overcurrent protection, and short-circuit protection to safeguard the device being powered from damage. Noise and Ripple: A power supply module should produce low levels of noise and ripple in the output voltage to prevent interference with other devices.

SPECIFICATIONS:

Part Number: DS3820PSWA
Manufacturer: General Electric
Series: Mark IV
Product Type: Power Supply Module
Power Requirements: +5 V dc, 6 A
Number of relay channels: 12
Power supply voltage: 28 V dc
Operating temperature: -40 to +70°C
Size: 15.9 cm high x 17.8 cm
Weight: 0.8kg
Repair: 3-7 Day
Availability: In Stock
Country of Origin: United States

Compatibility 

ƒ Compatible with any Series 90-30 CPU except IC693CPU321 and IC693CPU340. Configuration size is limited for CPU311/313/331, as described on the next page. 

ƒ Requires release 8.0 CPU firmware. The latest Release 10 is recommended, if available for the particular CPU. 

ƒ Requires CIMPLICITY Machine Edition Logic Developer PLC version 3.0 plus the appropriate service pack or special (or a version later than 3.0). 

ƒ Not compatible with the VersaPro™, Control, or Logicmaster™ programming software. 

ƒ The Series 90-30 Hand-Held Programmer (IC693PRG300) cannot be used to configure this module. New Features The Series 90-30 DeviceNet Master Module allows a Series 90-30 PLC to send and receive I/O data from a DeviceNet network. 

Module features include: 

ƒ Support for all standard data rates (125K, 250K, 500K) 

ƒ Support for 255 bytes input data transfer and 255 bytes output data transfer per slave 

ƒ Support for 3972 bytes of input data transfer and 3972 bytes of output data transfer per master 

ƒ Support for two I/O connections per Slave - Typically one connection is used for Polled and the other is used for Strobe, Cyclic, or COS 

ƒ Support for Poll, Strobe, Cyclic and COS I/O Connections, Fragmented I/O and Explicit Messaging 

ƒ Support for Unconnected Message Manager (UCMM) with 1 proxy connection per slave device 

ƒ Support for configuration of the global scan rate 

ƒ Support for configuration of update rates for Poll and COS/Cyclic on a connection basis 

ƒ Support for PLC-application initiated explicit messaging via a COMMREQ 

ƒ Master can be configured to operate as a slave simultaneously with master operation 

ƒ Configurable fault behavior on loss of communication 

ƒ Reports loss or reestablishment of communication with slaves in PLC fault table (configurable) 

ƒ Support for 64 network device status bits (note: the bit for the master itself is always zero) 

ƒ Firmware update via service port on module