GE IC3600VBCU1 Binary Counter Card

GE IC3600VBCU1 Binary Counter Card

Part Number IC3600VBCU1 Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VI/VIe Function Module Availability In StockIC3600VBCU1 is a Binary Counter Card manufactured and designed by General Electric. It is a part of the Mark I-II Series used in GE Speedtronic turbine control systems. These technologies, which aimed to increase the effectiveness of heavy-duty turbines, can be utilized to control anything from a single, unmanned pumping station with a capacity of 4000 HP to a multi-turbine power plant with a capacity of 400 Mw combined cycle. Eleven integrated circuits make up the IC3600VBCU1 device. Circuits are arranged on the board in two lines of four and one line of three. Seven diodes that have been attached to the board horizontally are inserted between these.

SPECIFICATIONS

Part Number: IC3600VBCU1
Manufacturer: General Electric
Series: Mark I-II
Product Type: Binary Counter Card
Board Size: 16.51 cm High x 17.8 cm
Repair: 3-7 Days
Weight: 2.00 lbs
Country of Origin: USA
Availability: In Stock

Compatibility 

ƒ Compatible with any Series 90-30 CPU except IC693CPU321 and IC693CPU340. Configuration size is limited for CPU311/313/331, as described on the next page. 

ƒ Requires release 8.0 CPU firmware. The latest Release 10 is recommended, if available for the particular CPU. 

ƒ Requires CIMPLICITY Machine Edition Logic Developer PLC version 3.0 plus the appropriate service pack or special (or a version later than 3.0). 

ƒ Not compatible with the VersaPro™, Control, or Logicmaster™ programming software. 

ƒ The Series 90-30 Hand-Held Programmer (IC693PRG300) cannot be used to configure this module. New Features The Series 90-30 DeviceNet Master Module allows a Series 90-30 PLC to send and receive I/O data from a DeviceNet network. Module features include: 

ƒ Support for all standard data rates (125K, 250K, 500K) 

ƒ Support for 255 bytes input data transfer and 255 bytes output data transfer per slave 

ƒ Support for 3972 bytes of input data transfer and 3972 bytes of output data transfer per master 

ƒ Support for two I/O connections per Slave - Typically one connection is used for Polled and the other is used for Strobe, Cyclic, or COS 

ƒ Support for Poll, Strobe, Cyclic and COS I/O Connections, Fragmented I/O and Explicit Messaging 

ƒ Support for Unconnected Message Manager (UCMM) with 1 proxy connection per slave device 

ƒ Support for configuration of the global scan rate 

ƒ Support for configuration of update rates for Poll and COS/Cyclic on a connection basis 

ƒ Support for PLC-application initiated explicit messaging via a COMMREQ 

ƒ Master can be configured to operate as a slave simultaneously with master operation 

ƒ Configurable fault behavior on loss of communication 

ƒ Reports loss or reestablishment of communication with slaves in PLC fault table (configurable) 

ƒ Support for 64 network device status bits (note: the bit for the master itself is always zero) 

ƒ Firmware update via service port on module

OTHER INFORMATION

• Available with either the 1.1 GHz, 1.6 GHz or 1.8 GHz  Pentium® M processor  

• 1.4 GHz Pentium M processor coming soon  

• Up to 2 Mbyte of advanced L2 cache  

• Up to 1.5 Gbyte DDR SDRAM  

• Up to 2 Gbyte bootable CompactFlash on secondary IDE (see  ordering options)  

• Internal SVGA and DVI controller  

• Serial ATA support through P2 rear I/O  

• 400 MHz system bus via Intel® 855GME chipset  

• Ethernet controller supporting 10BaseT and 100BaseTX  through the front panel  

• Gigabit Ethernet controller supporting 10BaseT, 100BaseTX  and 1000BaseT interface with optional VITA 31.1 support  

• Four asynchronous 16550 compatible serial ports  

• Four Universal Serial Bus (USB) Rev. 2.0 connections, two on  the front panel and two rear I/O  

• PMC expansion site (PCI-X, 66 MHz)  

• 32 Kbyte of nonvolatile SRAM  

• Operating system support for Windows® XP, Windows 2000,  VxWorks®, QNX® , LynxOS® and Linux