GE IS200VTURH2B VME TURBINE CARD

GE IS200VTURH2B VME TURBINE CARD

Part Number IS200VTURH2B Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VI Function Module Availability In StockIS200VTURH2B is a VME Turbine Card and is also known as the Primary Turbine Protection board under General Electric Speedtronic Mark VI series. The component performs several tasks, including monitoring shaft and voltage currents, as well as monitoring Geiger-Mueller flame detectors in gas turbine applications. To keep these processes running, the board monitors four-speed inputs from passive magnetic sensors. 

Flame detectors can help evaluate if the system's light detection is being hampered by carbon buildup or other impurities. In turbines without a mechanical Overspeed bolt, this PCB can also send a trip command A double-wide faceplate is used on the module. There are only a few components on this faceplate, but it does include three LED indicators and cable connectors. Three screws secure the faceplate to the front board edge. There are two backplane connectors on the board, as well as other connectors. On both the front and back of the board, there are thirteen transistors, inductor coils, resistors, and capacitors. 

An auxiliary board with an additional backplane is joined to the board via four standoffs. SRAM and RAM chips, oscillation chips, and FPGAs are among the integrated circuits on the board. This board is a VME turbine board that comes in a variety of configurations. This board was created to incorporate particular, unique interfaces from the turbine control system on a single card and monitors passive magnetic sensors from four-speed inputs. It works in conjunction with the Backup protection module's I/O interface in some applications. It has an attached faceplate with additional components such as LED status indicators and a cable connector placed into its surface. Two backplane connectors, inductor coils, capacitors, transistors, integrated circuits, and resistors are also on the board. The board is drilled in various places to make mounting easier.

OTHER INFORMATION

• Available with either the 1.1 GHz, 1.6 GHz or 1.8 GHz  Pentium® M processor  

• 1.4 GHz Pentium M processor coming soon  

• Up to 2 Mbyte of advanced L2 cache  

• Up to 1.5 Gbyte DDR SDRAM  

• Up to 2 Gbyte bootable CompactFlash on secondary IDE (see  ordering options)  

• Internal SVGA and DVI controller  

• Serial ATA support through P2 rear I/O  

• 400 MHz system bus via Intel® 855GME chipset  

• Ethernet controller supporting 10BaseT and 100BaseTX  through the front panel  

• Gigabit Ethernet controller supporting 10BaseT, 100BaseTX  and 1000BaseT interface with optional VITA 31.1 support  

• Four asynchronous 16550 compatible serial ports  

• Four Universal Serial Bus (USB) Rev. 2.0 connections, two on  the front panel and two rear I/O  

• PMC expansion site (PCI-X, 66 MHz)  

• 32 Kbyte of nonvolatile SRAM  

• Operating system support for Windows® XP, Windows 2000,  VxWorks®, QNX® , LynxOS® and Linux

Instructions and warnings related to the operation of the product:

The following specifications must be strictly observed:

 The technical specifications and typical applications of the product system must be strictly observed.

 PERSONNEL TRAINING: Only trained personnel may install, operate, maintain or repair the product system. These personnel must be instructed on the

These personnel must be instructed and briefed on the conditions in the hazardous area.

 Unauthorised modifications: No modifications or structural changes may be made to the product system.

 Maintenance Responsibility: It must be ensured that the product system is used only under appropriate conditions and in a condition fully suitable for use.

 Working environment: The user must fulfil the specified environmental conditions:

Safety regulations

The following safety regulations must be fully observed when (maintenance) work is carried out on the product system:

1 Disconnect completely.

2 Secure to prevent reconnection.

3 Confirm that the installation has been completed.

4 Perform grounding and short-circuiting.