GE IS210JPDDG3A - POWER DISTRIBUTION BOARD

GE IS210JPDDG3A - POWER DISTRIBUTION BOARD

Part Number IS210JPDDG3A Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VI/VIe Function Module Availability In StockIS210JPDDG3A is a DC Power Distribution Board manufactured and designed by General Electric as part of the Mark VIe Series used in GE Distributed Gas Turbine Control Systems. The DC Power Distribution (JPDD) board provides DC power distribution, power isolation, and branch circuit protection for control or I/O functions requiring 125 V DC, 48 V DC, or 24 V DC power. Typical applications include DC relay solenoid control power and contact wetting. 

Each output includes a fuse, a switch, and a lamp to indicate the presence of output voltage. JPDD is not intended for power distribution to the I/O packs. JPDDG1 provides fuses that are coordinated with the rating of the system wiring and connectors. JPDDG2 and G3 are used when fuse ratings coordinated with a specific application are required. Two different fuse sizes are provided to accommodate local fuse preferences. 

 INSTALLATION: JPDD is held in a plastic holder, which mounts on a vertical DIN rail. When installing the JPDD, it is important to provide a ground lead from TB1 to the system ground. This creates a ground path for the metal switch bodies. Power input can be 24 V DC, 48 V DC, or 125 V DC, but only one voltage level at any given time. OPERATION: Multiple JPDD boards can receive power from a single Main Power Distribution Module branch circuit. Power input can be either 125 V DC, 48 V DC, or 24 V DC nominal. Two 2-Pin Mate-N-Lok connectors are provided for 125 V DC power. 

One connector receives input power and the other can be used to distribute 125 V DC power to another JPDD board in a daisy chain fashion. Two 4-pin Mate-N-Lok connectors are provided for 24/48 V DC power. These perform functions similar to those of the 2-pin connectors above. The 4-pin connector permits parallel connection of two pin-pairs for increased current capacity. It is expected that neither side of the DC power input is grounded.Module manufactured by General Electric as part of the Mark VI/VIe Series used in gas turbine sppedtronic control systems

The Series 90-30 Hand-Held Programmer (IC693PRG300) cannot be used to configure this module. New Features The Series 90-30 DeviceNet Master Module allows a Series 90-30 PLC to send and receive I/O data from a DeviceNet network. 

Module features include: 

ƒ Support for all standard data rates (125K, 250K, 500K) 

ƒ Support for 255 bytes input data transfer and 255 bytes output data transfer per slave 

ƒ Support for 3972 bytes of input data transfer and 3972 bytes of output data transfer per master 

ƒ Support for two I/O connections per Slave - Typically one connection is used for Polled and the other is used for Strobe, Cyclic, or COS 

ƒ Support for Poll, Strobe, Cyclic and COS I/O Connections, Fragmented I/O and Explicit Messaging 

ƒ Support for Unconnected Message Manager (UCMM) with 1 proxy connection per slave device 

ƒ Support for configuration of the global scan rate 

ƒ Support for configuration of update rates for Poll and COS/Cyclic on a connection basis 

ƒ Support for PLC-application initiated explicit messaging via a COMMREQ 

ƒ Master can be configured to operate as a slave simultaneously with master operation 

ƒ Configurable fault behavior on loss of communication 

ƒ Reports loss or reestablishment of communication with slaves in PLC fault table (configurable) 

ƒ Support for 64 network device status bits (note: the bit for the master itself is always zero) 

ƒ Firmware update via service port on module

Compatibility 

ƒ Compatible with any Series 90-30 CPU except IC693CPU321 and IC693CPU340. Configuration size is limited for CPU311/313/331, as described on the next page. 

ƒ Requires release 8.0 CPU firmware. The latest Release 10 is recommended, if available for the particular CPU. 

ƒ Requires CIMPLICITY Machine Edition Logic Developer PLC version 3.0 plus the appropriate service pack or special (or a version later than 3.0). 

ƒ Not compatible with the VersaPro™, Control, or Logicmaster™ programming software.