SAST1 | General Electric Shunt Trip Circuit Breaker

SAST1 | General Electric Shunt Trip Circuit Breaker

Product Description P/N: SAST1 Description / Specifications Description The SAST1 is a General Electric shunt trip circuit breaker accessory compatible with Spectra RMS circuit breakers ranging from SE150 to SK1200. It facilitates remote tripping of the breaker when integrated with a momentary close contact, enhancing operational flexibility. Notably, continuous energization with a latching relay contact is discouraged due to potential delays in shunt tripping upon reclosure, though instantaneous short circuit trips are ensured. For applications requiring continuous operation without delay, alternatives like a bell alarm in series with control power are recommended for SE150 and SF250 frames, while an auxiliary switch is suitable for SG600 and SK1200 breakers. 

Technical Specifications Part Number SAST1 Category Circuit Breaker Subcategory Circuit Breaker Trip Specifications Manufacturer General Electric AC Voltage Rating 120 V DC Voltage Rating 125 V Frequency Rating 50/60 Hz Power Rating 75 VA Type Remote Used On SE150/SF250 Frame Circuit Breaker Approval UL PC ID 11870 PC TSPRODNAME SHUNT TRIP Information About SAST1 The SAST1 is a remote shunt trip accessory designed for General Electric's Spectra RMS circuit breakers, specifically applicable to models ranging from SE150 to SK1200, including Mag-Break motor circuit protectors and molded case switches. These accessories are UL listed and can be installed internally without requiring cover removal. 

The shunt trip mechanism enables remote tripping of the circuit breaker when triggered by a momentary close contact signal. It's important to note that continuous energization with a latching relay contact is not recommended due to potential pulsing of power to the coil, which can cause delayed shunt tripping upon reclosure, typically within 1-2 seconds at the rated control voltage. Instantaneous tripping, however, occurs during a short circuit fault. For applications where delayed shunt tripping is unacceptable with a latching relay contact, alternatives include using a bell alarm in conjunction with control power for SE150 and SF250 frames, or employing an auxiliary switch for SG600 and SK1200 breakers. 

 Key specifications of the SAST1 include a maximum power rating of 75 VA, compatibility with AC voltage at 120 V and DC voltage at 125 V, and operation within a frequency range of 50-60 Hz. It is designed for left pole mounting on SE150/SF250 frame circuit breakers within the Spectra RMS series. The SAST1 is a field-installed accessory that conforms to the authentic standards of General Electric products. Manufacturer information General Electric (GE)is a multinational conglomerate founded in 1892, based in the United States. It operates in various industries, including aviation, healthcare, renewable energy, and power. 

GE is known for its innovations in technology, manufacturing, and infrastructure solutions. IQElectro is not an authorized distributor. QElectro LLC (IQElectro) is NOT an Authorized Distributor or in any way affiliated with Rockwell Automation, Siemens, or any other Manufacturers. IQElectro is NOT an Authorized Dealer of this product. The product may be of older version, date codes, or design than that available from authorized dealers. As IQElectro is not an authorized dealer of this product, the Original Manufacturer's Warranty and Support DO NOT apply.IQElectro sells SURPLUS onlyand DOES NOT SELL SOFTWARE or FIRMWARE licenses For more detailed information, please refer to the full version of our disclaimer policy Disclaimer Policy.

The Series 90* -30 CPU374 PLUS provides a built-in enhanced Ethernet interface that  provides TCP/IP communications with: 

▪ Series 90, PACSystems, and VersaMax PLCs 

▪ Host computers running the Host Communications Toolkit or CIMPLICITY software 

▪ Computers running the TCP/IP version of the programming software CPU Features  

▪ High speed Boolean and non-Boolean processing provided by a 586-class 133MHz  processor 

▪ Two Ethernet ports: 10/100 Mbytes (one IP address) with a built-in, auto-sensing  Ethernet switch 

▪ Support for EZ Store Device allows you to download a program without a PC 

▪ 240KB of user memory Key Ethernet Features 

▪ Full PLC programming and configuration services 

▪ Periodic data exchange using Ethernet Global Data (EGD) and EGD commands to  read and write PLC and EGD exchange memory over the network 

▪ TCP/IP communication services using SRTP 

▪ Support for SRTP Client (Channels) 

▪ Modbus/TCP Server, supporting Modbus Conformance classes 0, 1, and 2. 

▪ Modbus/TCP Client, supporting Modbus Conformance classes 0, 1, and Function Codes 15, 22, 23, and 24 for Conformance class 2. 

▪ Remote PLC monitoring from a web browser 

▪ Comprehensive station management and diagnostic tools