THLK2200 | General Electric | Load Center Lug

THLK2200 | General Electric | Load Center Lug

Product Description P/N: DS3800HMPJ1A1D DESCRIPTION / SPECIFICATIONS Description The General Electric DS3800HMPJ1A1D is a Mark 4 Microprocessor Board, delivering advanced control and monitoring capabilities in industrial applications with precision and reliability. Technical Specifications Brand General Electric Category PLCs/Machine Control Part Number DS3800HMPJ1A1D Subcategory PC Board PLC/Add-On Board Information About DS3800HMPJ1A1D The DS3800HMPJ1A1D is a General Electric Mark IV circuit board. 

This board fits within the MKIV turbine control system designed to manage industrial gas and steam turbines of various sizes and complexity. The Mark IV was the first of the Speedtronic systems to increase reliability by using a TMR (triple modular redundant) arrangement. This use of duplicated processors voting on all inputs allowed for less downtime within the overall system. Designed with a backplane connector on one short edge and a cable connector on the other, the DS3800HMPJ1A1D is just one version of this board available within our warehouse stock. 

The board is marked with its ID number as well as several codes to aid with the position, wiring, and other board specifications. Codes may vary according to the individual unit sold. The DS3800HMPJ1A1D is built with a vertical pin connector. This is near four standoffs mounted to the board surface, allowing the addition of a secondary daughterboard that will communicate with the DS3800HMPJ1A1D through the cable connector. The board has over fifty integrated circuits including multiple PROMs/EPROMs. Other board components include LED indicators (one yellow, one red), resistor network arrays, resistors, diodes, capacitors, test points, and jumper switches. Jumpers are used to change settings on the board; this allows the board to be customized as the end-user requires. 

GE documentation will give more information on jumper settings. However, jumpers on your replacement board should typically match those of the board you are replacing. Manufacturer information General Electric (GE) is a multinational conglomerate founded in 1892, based in the United States. It operates in various industries, including aviation, healthcare, renewable energy, and power. GE is known for its innovations in technology, manufacturing, and infrastructure solutions. 

 IQElectro is not an authorized distributor. QElectro LLC (IQElectro) is NOT an Authorized Distributor or in any way affiliated with Rockwell Automation, Siemens, or any other Manufacturers. IQElectro is NOT an Authorized Dealer of this product. The product may be of older version, date codes, or design than that available from authorized dealers. As IQElectro is not an authorized dealer of this product, the Original Manufacturer's Warranty and Support DO NOT apply.IQElectro sells SURPLUS onlyand DOES NOT SELL SOFTWARE or FIRMWARE licenses For more detailed information, please refer to the full version of our disclaimer policy Disclaimer Policy.

OTHER INFORMATION

• Up to 1.26 GHz Pentium® III processor with 256 KB advanced  transfer cache  

• Up to 512 MB PC-133 SDRAM using a single SODIMM  

• Internal AGP SVGA controller with 4 MB display cache  

• 133 MHz system bus via Intel® 815E chipset  

• Dual Ethernet controllers supporting 10BaseT and 100BaseTX  interfaces  

• Optional PCI dual channel Ultra160 SCSI  

• Up to three (two with rear I/O support) PMC expansion sites  (IEEE-P1386 common mezzanine card standard, 5 V)  

• Up to 1 GB bootable flash on secondary IDE (optional)  

• Two 16-bit and two 32-bit programmable timers  

• 32 KB of nonvolatile SRAM  

• Software-selectable watchdog timer with reset  

• Remote Ethernet booting  

• Optional IDE hard disk drive  

• VME64 modes supported:  A32/A24/D32/D16/D08(EO)/MBLT64/BLT32  

• VMEbus interrupt handler, interrupter and system controller  

• Includes real time endian conversion hardware for littleendian and big-endian data interfacing (patent no. 6,032,212)  

• Enhanced bus error handling  

• Passive heat sink