GE DS200SBCAG1A Static Break Card

GE DS200SBCAG1A Static Break Card 

Part Number DS200SBCAG1A Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VI/VIe Function Module Availability In StockDS200SBCAG1A is a Static Brake Card developed by GE. The component is installed in a turbine control drive's inner mechanical system. The Speedtronic Mark V control systems provide a wide range of gas and steam turbine control applications. These adaptable, complicated control devices provide the monitoring and administration systems needed to regulate turbines. DS200SBCAG1A Features The typical Mark V drive features a triple modular redundancy architecture with software-implemented fault tolerance. It is connected to and put in the Mark V drives. This PCB is equipped with the static brake capabilities required by the drive. WOC has an inventory of unused excess as well as pre-owned, completely optimized, and reconditioned products. Our expert, on-site technical repair personnel performs the re-optimization. Our inventory is covered by a full, automatic warranty. Our coverage is available for up to three years.

This unit is listed as the DS200SBCAG1A, manufactured as a printed circuit board that is one of the many component parts that are installed in the inner mechanical system of a turbine control drive. This DS200 printed circuit board, as well as the control drive it is designed to be integrated into, are products from General Electric. GE manufactured these devices as a part of the Speedtronic Mark V control series. The Speedtronic Mark V control units are outfitted with extensive gas and steam turbine control applications, as flexible, complex control units that provide turbines with the monitoring and management systems required to regulate them. The standard Mark V drive is outfitted with a triple modular redundant architecture, as well as a software implemented fault tolerance. This DS200SBCAG1A Static Break Card is not the original product with its intended functionality to be manufactured for the Mark V Turbine Control System Series; that would be the DS200SBCAG1 parent Static Brake Card missing this DS200SBCAG1A PCB's A-rated functional product revision. 

Hardware Tips and Specifications

As alluded to before, this DS200SBCAG1A printed circuit board product offering makes use of its own series of hardware component inclusions and specifications to gain functional status as the Mark V Turbine Control System Series' Static Brake Card. For starters, this DS200SBCAG1A PCB is befitted with its own series of Mark V Series-standardized voltage-limiting and storing hardware components, ranging from sophisticated integrated circuits to various capacitors, diodes, and rectifiers typically seen in the normal assembly styles of Mark V Series printed circuit boards. The DS200SBCAG1A functional product number is considered a strong primary source of DS200SBCAG1A board-specific hardware component and specification information for this DS200SBCAG1A Static Brake Card, given its relative unavailability of original instructional manual materials. The DS200SBCAG1A functional product number begins with the DS200 series tag; dual-functional for the DS200SBCAG1A PCB as it describes both its normal Mark V Series assembly type and its domestic location of original manufacture. Some of the other important DS200SBCAG1A board hardware specifications revealed through analysis of the DS200SBCAG1A functional product number include:

The SBCA functional product acronym

A normal style of printed circuit board protective and insulating coating

A singular A-rated functional product revision

Compatibility 

ƒ Compatible with any Series 90-30 CPU except IC693CPU321 and IC693CPU340. Configuration size is limited for CPU311/313/331, as described on the next page. 

ƒ Requires release 8.0 CPU firmware. The latest Release 10 is recommended, if available for the particular CPU. 

ƒ Requires CIMPLICITY Machine Edition Logic Developer PLC version 3.0 plus the appropriate service pack or special (or a version later than 3.0). 

ƒ Not compatible with the VersaPro™, Control, or Logicmaster™ programming software. 

ƒ The Series 90-30 Hand-Held Programmer (IC693PRG300) cannot be used to configure this module. New Features The Series 90-30 DeviceNet Master Module allows a Series 90-30 PLC to send and receive I/O data from a DeviceNet network. 

Module features include: 

ƒ Support for all standard data rates (125K, 250K, 500K) 

ƒ Support for 255 bytes input data transfer and 255 bytes output data transfer per slave 

ƒ Support for 3972 bytes of input data transfer and 3972 bytes of output data transfer per master 

ƒ Support for two I/O connections per Slave - Typically one connection is used for Polled and the other is used for Strobe, Cyclic, or COS 

ƒ Support for Poll, Strobe, Cyclic and COS I/O Connections, Fragmented I/O and Explicit Messaging 

ƒ Support for Unconnected Message Manager (UCMM) with 1 proxy connection per slave device 

ƒ Support for configuration of the global scan rate 

ƒ Support for configuration of update rates for Poll and COS/Cyclic on a connection basis 

ƒ Support for PLC-application initiated explicit messaging via a COMMREQ 

ƒ Master can be configured to operate as a slave simultaneously with master operation 

ƒ Configurable fault behavior on loss of communication 

ƒ Reports loss or reestablishment of communication with slaves in PLC fault table (configurable) 

ƒ Support for 64 network device status bits (note: the bit for the master itself is always zero) 

ƒ Firmware update via service port on module