GE DS200TCCBG1B I/O TC2000 Analog Board

GE DS200TCCBG1B I/O TC2000 Analog Board

Part Number DS200TCCBG1B Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark V Function Module Availability In StockDS200TCCBG1B is an I/O TC2000 Analog Board and is part of the GE Speedtronic Mark V gas turbine control systems. The DS200TCCBG1B General Electric I/O TC2000 Analog Board has one 80196 CPU and numerous PROM modules. One LED and two 50-pin connectors are also included. From the side of the board, the LED is visible. JCC and JDD are the IDs for the 50-pin connectors. Three jumpers are also present on the board. 

The IDs of the jumpers are printed on the board's surface. JP1, JP2, and JP3 are the IDs. When the original board is put in the drive, the installer configures it to meet the drive's specifications to the best of his ability. By adjusting the position of the jumpers, the installer can change the configuration values. Under most circumstances, the jumper positions are used by default, and the installer does not need to do anything else. However, in other cases, the installer adjusts the jumper's position based on the information provided in the written paperwork that comes with the board. 

The jumper in a 3-pin jumper covers two pins at a time. The jumper could, for example, cover pins 1 and 2 or pins 2 and 3. Grab the jumper with your thumb and forefinger and pull it away from the pins to shift it. Then slip the jumper into place, aligning it with the new pins. Some jumpers are only supported in one location and are not utilized for board configuration. In this example, the alternate position is used by the manufacturer for product testing to check a certain circuit or function. 2PL, 3PL, JHH, JII, JMP, JKK, JTEST, and TCQPL are the eight connectors on the board. JKK, JTEST, and TCQPL Connectors are typically not used.

Features 

Single-Slot Module 

SNP/SNP-X Protocol (master, slave) 

CCM Protocol (master, slave, peer) 

RTU Modbus Protocol (slave only) 

Supports connection to MS-DOS

 or Windows

 programming and configuration software package (monitor only) 

12 Mhz, 80C186 Microprocessor 

Two RS-422/RS-485 or RS-232 Serial Ports 

CCM, RTU and SNP/SNP-X Available on Either or Both Ports 

Simultaneous Communications on Both Ports (up to 9.6 Kbps, or 19.2 Kbps individually) 

High Performance Access to PLC Memory 

Three Status LEDs 

Reset pushbutton 

Soft Switch Configuration (no switches or jumpers) 

No Battery Required

Features 

Single slot CPU 

Provides 1 Mbyte of battery-backed memory in the same slot (up to 512 Kbytes available for use by ladder diagram application program)
Supports floating point calculations 

Up to 12K discrete inputs and outputs (any mix - simplex mode only); 2048 voted discrete inputs, 2048 voted discrete outputs Up to 8K analog inputs (simplex mode only) and 8K analog outputs (simplex mode only); 1024 voted analog inputs 

0.4 microseconds per boolean function 

64 MHz, 80486DX2 microprocessor 

Supports IC660/IC661 I/O (and IC697 I/O in simplex mode only) 

Programmed by MS-DOS, or Windows

 software products running on Windows

 95 or Windows NT

 over Ethernet TCP/IP or through the SNP port. 

Configurable data and program memory 

Battery-backed calendar clock 

Three position operation mode switch 

Password controlled access 

Remote programmer keyswitch memory protection 

Four status LEDs 

Software configuration (No DIP switches or jumpers) 

Reference information inside front door 

In-system upgradable firmware