GE DS3800DLCA DAUGHTER BOARD

GE DS3800DLCA DAUGHTER BOARD

Part Number DS3800DLCA Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VI/VIe Function Module Availability In StockGE Speedtronic Mark IV DS3800DLCA is a printed circuit board and its series of Mark IV gas and steam turbine control systems. The DS3800DLCA functions as a load communication converter card that was built expressly for that purpose. In this way, in the event of a malfunction, control, and communications can be shifted, and the Mark IV system can continue to operate without being shut down while the particular electronic board is evaluated and repaired. 

The DS3800DLCA was designed with only one mounting option in mind. All four corners of the board are drilled. There is only one test point ring on it. The ring is labeled TP12 and is placed near the potentiometer on the board's edge. There is only one potentiometer on it. The part number is 3069P-1-203. 20A. There is one ribbon cable connector on the board's long edge, as well as six communication connections. These run between the labels "Open Com" and "Cov" and are parallel to the potentiometer. Each one is identified by the letters BJ1 through BJ6. There are three different types of resistors on the board. There are five capacitors designated 70801 on the PCB. On the border of the DS3800DLCA are the letters 6BA03, DLCA, and 6DA02. A triangle logic buffer sign is also present on the board.

Compatibility 

ƒ Compatible with any Series 90-30 CPU except IC693CPU321 and IC693CPU340. Configuration size is limited for CPU311/313/331, as described on the next page. 

ƒ Requires release 8.0 CPU firmware. The latest Release 10 is recommended, if available for the particular CPU. 

ƒ Requires CIMPLICITY Machine Edition Logic Developer PLC version 3.0 plus the appropriate service pack or special (or a version later than 3.0). 

ƒ Not compatible with the VersaPro™, Control, or Logicmaster™ programming software. 

ƒ The Series 90-30 Hand-Held Programmer (IC693PRG300) cannot be used to configure this module. New Features The Series 90-30 DeviceNet Master Module allows a Series 90-30 PLC to send and receive I/O data from a DeviceNet network. 

Module features include: 

ƒ Support for all standard data rates (125K, 250K, 500K) 

ƒ Support for 255 bytes input data transfer and 255 bytes output data transfer per slave 

ƒ Support for 3972 bytes of input data transfer and 3972 bytes of output data transfer per master 

ƒ Support for two I/O connections per Slave - Typically one connection is used for Polled and the other is used for Strobe, Cyclic, or COS 

ƒ Support for Poll, Strobe, Cyclic and COS I/O Connections, Fragmented I/O and Explicit Messaging 

ƒ Support for Unconnected Message Manager (UCMM) with 1 proxy connection per slave device 

ƒ Support for configuration of the global scan rate 

ƒ Support for configuration of update rates for Poll and COS/Cyclic on a connection basis 

ƒ Support for PLC-application initiated explicit messaging via a COMMREQ 

ƒ Master can be configured to operate as a slave simultaneously with master operation 

ƒ Configurable fault behavior on loss of communication 

ƒ Reports loss or reestablishment of communication with slaves in PLC fault table (configurable) 

ƒ Support for 64 network device status bits (note: the bit for the master itself is always zero) 

ƒ Firmware update via service port on module

SPECIFICATIONS

Input voltage：110V-380V

Electric current：1A-30A

Power： 5W-130W

Warranty period：1 year

Stock Quantity：30

Place of origin：United States, France, Japan, Viet Nam, Australia, Russia, Germany, Italy, Arabia