GE DS3800NFMC FAULT FINDER LED INDICATOR BOARD

GE DS3800NFMC FAULT FINDER LED INDICATOR BOARD

Part Number DS3800NFMC Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VI/VIe Function Module Availability In StockDS3800NFMC is a Fault Finder LGT Display Board developed by General Electric under the Mark IV series. This item is part of the Speedtronic Mark IV series, which is responsible for turbine control. The DS3800NFMC functions as a fault-finder LED indicator module. The Board has a lot of key components. The DS3800NFMC has 38 integrated circuits, which takes up a lot of room. A lengthy connector port runs the length of the DS3800NFMC's left side. Users can utilize this port by connecting other boards or components to it. On the right side of the component, nine LEDs are arranged. 

Near the LEDs is a cluster of 15 test points. The initials TP are used to identify each test point, which is labeled TP1 through TP15. These test points can be used by operators to confirm that the card is functioning properly. The card also has a selection of capacitors in various sizes and colors. On the right side of the board, there are two medium-sized silver capacitors. A silver capacitor can be found towards the board's upper edge. The DS3800NFMC has several capacitors with distinct color bands. The module also comes with a variety of resistors. On the left half of the board, nineteen black spherical transistors with the letter Q are arranged in rows of three and four.

Compatibility 

ƒ Compatible with any Series 90-30 CPU except IC693CPU321 and IC693CPU340. Configuration size is limited for CPU311/313/331, as described on the next page. 

ƒ Requires release 8.0 CPU firmware. The latest Release 10 is recommended, if available for the particular CPU. 

ƒ Requires CIMPLICITY Machine Edition Logic Developer PLC version 3.0 plus the appropriate service pack or special (or a version later than 3.0). 

ƒ Not compatible with the VersaPro™, Control, or Logicmaster™ programming software. 

ƒ The Series 90-30 Hand-Held Programmer (IC693PRG300) cannot be used to configure this module. New Features The Series 90-30 DeviceNet Master Module allows a Series 90-30 PLC to send and receive I/O data from a DeviceNet network. 

Module features include: 

ƒ Support for all standard data rates (125K, 250K, 500K) 

ƒ Support for 255 bytes input data transfer and 255 bytes output data transfer per slave 

ƒ Support for 3972 bytes of input data transfer and 3972 bytes of output data transfer per master 

ƒ Support for two I/O connections per Slave - Typically one connection is used for Polled and the other is used for Strobe, Cyclic, or COS 

ƒ Support for Poll, Strobe, Cyclic and COS I/O Connections, Fragmented I/O and Explicit Messaging 

ƒ Support for Unconnected Message Manager (UCMM) with 1 proxy connection per slave device 

ƒ Support for configuration of the global scan rate 

ƒ Support for configuration of update rates for Poll and COS/Cyclic on a connection basis 

ƒ Support for PLC-application initiated explicit messaging via a COMMREQ 

ƒ Master can be configured to operate as a slave simultaneously with master operation 

ƒ Configurable fault behavior on loss of communication 

ƒ Reports loss or reestablishment of communication with slaves in PLC fault table (configurable) 

ƒ Support for 64 network device status bits (note: the bit for the master itself is always zero) 

ƒ Firmware update via service port on module

APPLICATIONS

• Simulation 

• Instrumentation 

• Industrial control 

• Process control and monitoring 

• Factory automation 

• Intelligent networked PLC controllers 

• Automated test 

• Data acquisition