GE DS200DTBDG1A Contact Output Expansion Termination Module

GE DS200DTBDG1A Contact Output Expansion Termination Module

Part Number DS200DTBDG1A Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark V Function Module Availability In StockDS200DTBDG1A is a Contact Output Expansion Termination Module manufactured and designed by General Electric as part of the Mark V/ Mark V LM Series used in turbine control systems. Locations for the Contact Output Expansion Termination Module (DTBD) include Q11, Q21, and Q51. In position 5 of Q11, Q21, and Q51 on the TCRA, DTBD is connected to the 30 relays. By using hardware jumpers on DTBD, 16 of the 30 outputs on location 4 of Q21 and Q51 can be set up as solenoids. 

When J19 and J20 are linked and the factory-installed wire jumpers are changed, two more contact outputs (#47 and #48) can be used for ignition converters. DS200DTBDG1A Connectors JS1 through JS8 - Reads the relay signals from the TCRA board at position five using JS1 through JS8. J8 - The TCPD board in the PD core supplies power to J8 for the solenoids. J19 - To supply 125 V dc power to contact outputs #47 and #48, J19 is connected to J20. Linked in Q11 and Q51, not connected in Q21. J20 - Connects to J19 to supply contact outputs #47 and #48 with 125 V dc power. 

Linked in Q11 and Q51, not connected in Q21. DTBD Hardware Configuration P1/M1 through P16/M16 - For contact outputs #31 through #46, respectively, solenoid enable. Both must be inside or outside. Features The test points on the board have an ID that starts with TP and ends with a number. Some examples include TP1 and TP2. The IDs are crucial because the servicer can look up information about the test spots in the written publication that comes with the board from the factory. The test point ID will be used to reference the data. It will what TP1 is for, what circuits the test point checks, and what the testing numbers represent. 

If you notice that the board is not performing as expected, consult the instructions and test the circuits that may be affected. Only a trained servicer, on the other hand, will have the necessary background, expertise, and understanding to test the board. The board-testing equipment must be qualified for the job, completely functioning, and in good operating order. The tester must also be calibrated for the task, and the probes must be designed for use with the tester. They also need to be in good operating order. Place the board on top of a static-free surface to safeguard it. For example, a static protective bag that has been flattened. It is necessary to have a clean and dry surface. The surface should be solid, with enough room for hand tools, testing equipment, other boards, and printed instructions.

Hardware Tips and Specifications

The GE Terminal Board DS200DTBDG1A features 2 terminal blocks. Each block contains 107 terminals for signal wires. The GE Terminal Board DS200DTBDG1A also contains multiple test points, 2 jumpers, and 3 34-pin connectors. The ID of the test points on the board begin with TP and end with a number. TP1 and TP2 are some examples. The IDs are important because the servicer can refer to the written publication that ships with the board from the factory for information about the test points. However, only a trained servicer will have the background, experience and knowledge to test the board. The testing equipment used to test the board must be qualified for the purpose, fully functional, and in good working order. This testing equipment must also be calibrated for the task; in good working condition with probes intended for testing attachment.

While it certainly is important ot be cognizant of safe and normative testing processes for this DS200DTBDG1A Contact Output Expansion Termination Module, it is important too to identify some of the various connectors adopted into the assembly of this Mark V Series product. These connectors include:

The J8 TCPD board solenoid power connector

The J19 125 V dc 47 and 48 contacts output power connector

The J20  125 V dc 47 and 48 contacts output power connector

Our Main Brands

· - ABB Advant-800xA，Advant OCS，Bailey Infi 90 and Net 90，H&B Freelance 2000，DSQC Robots，IGCT / IGBT

· - GE General Electric Field Control, Genius I/O, QuickPanel, RX3i PacSystem, Series 90, Series 90, Series VersaMax

· - Allen Bradley Allen-Bradley SLC500, MicroLogix, CompactLogix, ControlLogix, PLC-5, Panel View,

· - Bently Nevada 3300 System, 3500 System

· - Honeywell 7800 Series, FSC, IPC, Mxopen, TDC 2000, TDC 3000, Experion PKS(C200,C300)

· - Yokogawa Centum CS - Centum VP, Centum XL - micro XL, FA-M3, ProSafe-PLC

· - Ovation, Foxboro, EPRO, Emerson DeltaV, Fuji, Siemens, HIMA, Prosoft, Invensys Triconex, ICS TRIPLEX, Woodward, Bachmann, Schneider