GE IC3600ADAD1 Speedtronic Diode D/A Converter Board

GE IC3600ADAD1 Speedtronic Diode D/A Converter Board

Part Number IC3600ADAD1 Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VI/VIe Function Module Availability In StockIC3600ADAD1A is a Diode D/A Converter Board manufactured by General Electric Fanuc as part of the Mark II series used in gas turbine control management systems. With some processes having single or double redundancies built-in to ensure reliability and safe machine operation, the Mark II utilized integrated circuits and microprocessors to carry out control, sequencing, and protection duties. 

Through-hole fixed components are used to construct the converter board. You can attach components either vertically or horizontally. Diodes, resistors, and capacitors are included in this. Two aluminum electrolytic capacitors with a 50V rating and two polyester vinyl capacitors with a 200 VDC +/- 10% rating are among the capacitors on the board. Three trim potentiometers are also integrated into the board and are placed parallel to one another in the corner.

Compatibility 

ƒ Compatible with any Series 90-30 CPU except IC693CPU321 and IC693CPU340. Configuration size is limited for CPU311/313/331, as described on the next page. 

ƒ Requires release 8.0 CPU firmware. The latest Release 10 is recommended, if available for the particular CPU. 

ƒ Requires CIMPLICITY Machine Edition Logic Developer PLC version 3.0 plus the appropriate service pack or special (or a version later than 3.0). 

ƒ Not compatible with the VersaPro™, Control, or Logicmaster™ programming software. 

ƒ The Series 90-30 Hand-Held Programmer (IC693PRG300) cannot be used to configure this module. New Features The Series 90-30 DeviceNet Master Module allows a Series 90-30 PLC to send and receive I/O data from a DeviceNet network. 

Module features include: 

ƒ Support for all standard data rates (125K, 250K, 500K) 

ƒ Support for 255 bytes input data transfer and 255 bytes output data transfer per slave 

ƒ Support for 3972 bytes of input data transfer and 3972 bytes of output data transfer per master 

ƒ Support for two I/O connections per Slave - Typically one connection is used for Polled and the other is used for Strobe, Cyclic, or COS 

ƒ Support for Poll, Strobe, Cyclic and COS I/O Connections, Fragmented I/O and Explicit Messaging 

ƒ Support for Unconnected Message Manager (UCMM) with 1 proxy connection per slave device 

ƒ Support for configuration of the global scan rate 

ƒ Support for configuration of update rates for Poll and COS/Cyclic on a connection basis 

ƒ Support for PLC-application initiated explicit messaging via a COMMREQ 

ƒ Master can be configured to operate as a slave simultaneously with master operation 

ƒ Configurable fault behavior on loss of communication 

ƒ Reports loss or reestablishment of communication with slaves in PLC fault table (configurable) 

ƒ Support for 64 network device status bits (note: the bit for the master itself is always zero) 

ƒ Firmware update via service port on module

Features 

 Single-Slot Module 

 SNP/SNP-X Protocol (master, slave) 

 CCM Protocol (master, slave, peer) 

 RTU Modbus Protocol (slave only) 

 Supports connection to MS-DOS or Windows

 programming and configuration software package (monitor only) 

 12 Mhz, 80C186 Microprocessor 

 Two RS-422/RS-485 or RS-232 Serial Ports 

 CCM, RTU and SNP/SNP-X Available on Either or Both Ports 

 Simultaneous Communications on Both Ports (up to 9.6 Kbps, or 19.2 Kbps individually) 

 High Performance Access to PLC Memory 

 Three Status LEDs 

 Reset pushbutton 

 Soft Switch Configuration (no switches or jumpers) 

 No Battery Required