GE ds215uplag1bzz01a Power Supply Board

GE ds215uplag1bzz01a Power Supply Board

Part Number ds215uplag1bzz01a Manufacturer General Electric Country of Manufacture As Per GE Manufacturing Policy Series Mark VI/VIe Function Module Availability In StockDS215UPLAG1BZZ01A is a Power Supply/LAN Interface Board with firmware manufactured by General Electric as part of the EX2000 series used in excitation control systems. With on-board EEPROMS that update the firmware appropriately, it is an improved version of the DS200UPLAG1A. DS215UPLAG1BZZ01A Features There is a single reset button, 28 jumpers, and 2 banks of configuration switches on the board. 

Additionally, there are 2 indicator LEDs and 1 fuse on the GE Drive Systems UPLAG Board. One green Power On LED, which illuminates when power is present on the board, is found on the GE Drive Systems UPLAG Board. When the LED is not lighted, power is not present. A board problem is shown by the 1 red LED. It is best practice to initially hit the reset button on the board if an error has occurred. By pressing this button, the board's processing can be restarted without the board losing power. Restarting your computer might fix any errors that have happened. DS215UPLAG1BZZ01A Hardware Components The following are the major hardware components of this UPLA board: 115/230 V ac, 50/60 Hz to 24 V, and a 5 V switching power supply Power-on reset and 5 V Undervoltage detect Microprocessor core Flash (non-volatile) memory capability DLAN+ interface port RS-232C serial port When the reset button is pressed during power up or whenever the 5 V logic supply voltage falls below 4.6 V, the reset is initiated.

OTHER INFORMATION

• Available with either the 1.1 GHz, 1.6 GHz or 1.8 GHz  Pentium® M processor  

• 1.4 GHz Pentium M processor coming soon  

• Up to 2 Mbyte of advanced L2 cache  

• Up to 1.5 Gbyte DDR SDRAM  

• Up to 2 Gbyte bootable CompactFlash on secondary IDE (see  ordering options)  

• Internal SVGA and DVI controller  

• Serial ATA support through P2 rear I/O  

• 400 MHz system bus via Intel® 855GME chipset  

• Ethernet controller supporting 10BaseT and 100BaseTX  through the front panel  

• Gigabit Ethernet controller supporting 10BaseT, 100BaseTX  and 1000BaseT interface with optional VITA 31.1 support  

• Four asynchronous 16550 compatible serial ports  

• Four Universal Serial Bus (USB) Rev. 2.0 connections, two on  the front panel and two rear I/O  

• PMC expansion site (PCI-X, 66 MHz)  

• 32 Kbyte of nonvolatile SRAM  

• Operating system support for Windows® XP, Windows 2000,  VxWorks®, QNX® , LynxOS® and Linux

Instructions and warnings related to the operation of the product:

The following specifications must be strictly observed:

 The technical specifications and typical applications of the product system must be strictly observed.

 PERSONNEL TRAINING: Only trained personnel may install, operate, maintain or repair the product system. These personnel must be instructed on the

These personnel must be instructed and briefed on the conditions in the hazardous area.

 Unauthorised modifications: No modifications or structural changes may be made to the product system.

 Maintenance Responsibility: It must be ensured that the product system is used only under appropriate conditions and in a condition fully suitable for use.

 Working environment: The user must fulfil the specified environmental conditions:

Safety regulations

The following safety regulations must be fully observed when (maintenance) work is carried out on the product system:

1 Disconnect completely.

2 Secure to prevent reconnection.

3 Confirm that the installation has been completed.

4 Perform grounding and short-circuiting.