GE Fanuc IS215UCVGH1A Industrial Control Card

GE Fanuc IS215UCVGH1A Industrial Control Card

Processor Speed:200 MHz Memory Size:64 MB Network Compatibility:EtherNet/IP I/O Capacity:16 Digital Inputs, 16 Digital Outputs Power Consumption:10 W The GE-FANUC IS215UCVGH1A Controller Card is engineered with state-of-the-art technology to ensure seamless integration into complex automation systems. Its robust floating-point processing capabilities and low-speed memory capacity make it an ideal choice for applications requiring high precision and performance. Featuring a compact design that fits into tight spaces, this controller card is compatible with multiple hardware platforms, including RX7i, RX3i, and Quick Panel Control, providing versatility and flexibility for diverse industrial setups. 

 With support for standard industrial communication protocols like Profibus鈩?and DeviceNet鈩? the IS215UCVGH1A ensures smooth data exchange and efficient system operation. Its advanced Ethernet interface based on the latest Wire鈩?standard significantly boosts I/O update speeds, enhancing overall system responsiveness and productivity. This controller card is designed with redundancy in mind, making it suitable for critical applications where reliability is paramount. It supports seamless integration with existing GE Fanuc control systems, allowing for a smooth transition without compromising on performance or investment protection. 

 Backed by comprehensive documentation and a suite of tools for configuration and diagnostics, the IS215UCVGH1A simplifies installation and maintenance processes. Its compatibility with Proficy庐 ME programming environment further enhances its usability, streamlining the development and management of automation projects. The GE Fanuc IS215UCVGH1A Controller Card is a versatile component designed for industrial automation systems, offering seamless integration and control in complex manufacturing environments.

Compatibility 

ƒ Compatible with any Series 90-30 CPU except IC693CPU321 and IC693CPU340. Configuration size is limited for CPU311/313/331, as described on the next page. 

ƒ Requires release 8.0 CPU firmware. The latest Release 10 is recommended, if available for the particular CPU. 

ƒ Requires CIMPLICITY Machine Edition Logic Developer PLC version 3.0 plus the appropriate service pack or special (or a version later than 3.0). 

ƒ Not compatible with the VersaPro™, Control, or Logicmaster™ programming software. 

ƒ The Series 90-30 Hand-Held Programmer (IC693PRG300) cannot be used to configure this module. New Features The Series 90-30 DeviceNet Master Module allows a Series 90-30 PLC to send and receive I/O data from a DeviceNet network. 

Module features include: 

ƒ Support for all standard data rates (125K, 250K, 500K) 

ƒ Support for 255 bytes input data transfer and 255 bytes output data transfer per slave 

ƒ Support for 3972 bytes of input data transfer and 3972 bytes of output data transfer per master 

ƒ Support for two I/O connections per Slave - Typically one connection is used for Polled and the other is used for Strobe, Cyclic, or COS 

ƒ Support for Poll, Strobe, Cyclic and COS I/O Connections, Fragmented I/O and Explicit Messaging 

ƒ Support for Unconnected Message Manager (UCMM) with 1 proxy connection per slave device 

ƒ Support for configuration of the global scan rate 

ƒ Support for configuration of update rates for Poll and COS/Cyclic on a connection basis 

ƒ Support for PLC-application initiated explicit messaging via a COMMREQ 

ƒ Master can be configured to operate as a slave simultaneously with master operation 

ƒ Configurable fault behavior on loss of communication 

ƒ Reports loss or reestablishment of communication with slaves in PLC fault table (configurable) 

ƒ Support for 64 network device status bits (note: the bit for the master itself is always zero) 

ƒ Firmware update via service port on module